Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 19, Problem 1SQ

To determine

Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Expert Solution & Answer

Explanation of Solution

If the contacts of the selector switch and automatic pilot device are large enough to pass the safety full-load current of motor, then they can control the motor directly, but the contact capacity of these devices is generally not large enough for huge motors.

Hence, these devices cannot be utilized to control the motor directly.

These two devices are connected to magnetic starter for controlling a large motor.

Conclusion:

Thus, the given statement is explained.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

A three-phase transmission line supplies power to three loads at a voltage 408 Vrms (line to line). The loads are as follows: Load 1: S₁ = 100+ j50 VA Load 2: S₂ = 40-j20 VA Load 3: S3 = 10 + j0 VA Find the magnitude of the line current | Line and the combined power factor of the loads. Hint: Steral \= √3 | Vime |× | Ime | line line

Can you show why the answer to this question R = 199 ohm?

2.5. Find the half-power beamwidth (HPBW) and first-null beamwidth (FNBW), in radians and degrees, for the following normalized radiation intensities: (a) U(9) cos θ cos(20) (b) U(θ)-cos2 θ cos2(26) (c) U(θ) = cos(θ) cos(30) (0 < θ < 900,0 < φ 360) (d) U(t) = cos2(9) cos2(39) (e) U(9) = cos(29) cos(39) (f) U (ecos (20) cos (30)

Answer 2

Question

Chapter 19, Problem 1SQ

To determine

Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Expert Solution & Answer

Explanation of Solution

If the contacts of the selector switch and automatic pilot device are large enough to pass the safety full-load current of motor, then they can control the motor directly, but the contact capacity of these devices is generally not large enough for huge motors.

Hence, these devices cannot be utilized to control the motor directly.

These two devices are connected to magnetic starter for controlling a large motor.

Conclusion:

Thus, the given statement is explained.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 19, Problem 1SQ

To determine

Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Expert Solution & Answer

Explanation of Solution

If the contacts of the selector switch and automatic pilot device are large enough to pass the safety full-load current of motor, then they can control the motor directly, but the contact capacity of these devices is generally not large enough for huge motors.

Hence, these devices cannot be utilized to control the motor directly.

These two devices are connected to magnetic starter for controlling a large motor.

Conclusion:

Thus, the given statement is explained.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 19, Problem 1SQ

To determine

Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Expert Solution & Answer

Explanation of Solution

If the contacts of the selector switch and automatic pilot device are large enough to pass the safety full-load current of motor, then they can control the motor directly, but the contact capacity of these devices is generally not large enough for huge motors.

Hence, these devices cannot be utilized to control the motor directly.

These two devices are connected to magnetic starter for controlling a large motor.

Conclusion:

Thus, the given statement is explained.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 19, Problem 1SQ

To determine

Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Expert Solution & Answer

Explanation of Solution

If the contacts of the selector switch and automatic pilot device are large enough to pass the safety full-load current of motor, then they can control the motor directly, but the contact capacity of these devices is generally not large enough for huge motors.

Hence, these devices cannot be utilized to control the motor directly.

These two devices are connected to magnetic starter for controlling a large motor.

Conclusion:

Thus, the given statement is explained.

Answer 6

Chapter 19, Problem 1SQ

To determine

Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Expert Solution & Answer

Explanation of Solution

If the contacts of the selector switch and automatic pilot device are large enough to pass the safety full-load current of motor, then they can control the motor directly, but the contact capacity of these devices is generally not large enough for huge motors.

Hence, these devices cannot be utilized to control the motor directly.

These two devices are connected to magnetic starter for controlling a large motor.

Conclusion:

Thus, the given statement is explained.

Answer 7

Chapter 19, Problem 1SQ

To determine

Explain why the selector switch and a two-wire pilot device should be connected to the magnetic starter to control a large motor and they cannot be controlled directly.

Answer 8

Expert Solution & Answer

Explanation of Solution

If the contacts of the selector switch and automatic pilot device are large enough to pass the safety full-load current of motor, then they can control the motor directly, but the contact capacity of these devices is generally not large enough for huge motors.

Hence, these devices cannot be utilized to control the motor directly.

These two devices are connected to magnetic starter for controlling a large motor.

Conclusion:

Thus, the given statement is explained.