(a)
Interpretation:
Picture that represents the solution just after the solid
Concept introduction:
Solubility:
Solubility is a chemical property of a given substance i.e. solute to dissolve in solvent.
For slightly soluble salts the solute dissolves in little amount in solvent to give respective ions and there is always an equilibrium between the ions of the salt and the unionized molecules.
(b)
Interpretation:
Value of
Concept introduction:
Solubility:
Solubility is defined as the maximum amount of the solute that can be dissolved in the solvent at equilibrium.
Solubility product constant:
Solubility product constant is defined for equilibrium between solids and its respective ions in the solution. Generally, solubility product refers only to insoluble or slightly soluble ionic substances that make equilibrium in water.
It is defined as the product of concentration of ions of a sparingly soluble salt in its saturated solution at
This value indicates the degree of dissociation of a compound in water. More the value of
Considering an equilibrium of salt
(c)
Interpretation:
Figure representing the solution after addition of
Concept introduction:
Common ion effect:
Suppression of ionization of a weak electrolyte by the addition of a strong electrolyte in the same solution and one ion must be common in between both the weak and strong electrolyte.
Le Chatelier’s principle:
When a system in equilibrium is subjected to any external disturbance like change of pressure, volume, temperature etc…Then the system acts in a way to prevent that change. This is called Le Chatelier’s principle.
(d)
Interpretation:
The scene that interprets the situation after lowering of
Concept introduction:
Chemical equilibrium is the process where the
Le Chatelier’s principle:
When a system in equilibrium is subjected to any external disturbance like change of pressure, volume, temperature etc… Then the system acts in a way to prevent that change. This is called Le Chatelier’s principle.
Want to see the full answer?
Check out a sample textbook solutionChapter 19 Solutions
Chemistry: The Molecular Nature of Matter and Change - Standalone book
- This thermodynamic cycle describes the formation of an ionic compound MX2 from a metal element M and nonmetal element X in their standard states. What is the lattice enthalpy of MX2 ? What is the enthalpy formation of MX2 ? Suppose both the heat of sublimation of M and the ionization enthalpy of M were smaller. Would MX2 be more stable? Or less? or impossible to tell without more information?arrow_forward7. Draw the mechanism to describe the following transformation: Note: This is a base catalyzed reaction. So, the last steps must make [OH]- OH [OH]¯ OH Heat Oarrow_forwardShow work with explanation...don't give Ai generated solutionarrow_forward
- Br. , H+ .OH Mg ether solvent H+, H₂O 17. Which one of the compounds below is the final product of the reaction sequence shown above? HO A HO HO OH D B OH HO OH C OH HO OH Earrow_forward8:57 PM Sun Jan 26 Content ← Explanation Page X Content X ALEKS Jade Nicol - Le A https://www-av C www-awa.aleks.com O States of Matter Understanding consequences of important physical properties of liquids ? QUESTION Liquid A is known to have a lower viscosity and lower surface tension than Liquid B. Use these facts to predict the result of each experiment in the table below, if you can. experiment Liquid A and Liquid B are each pumped through tubes with an inside diameter of 27.0 mm, and the pressures PA and PB needed to produce a steady flow of 2.4 mL/s are measured. 25.0 mL of Liquid A are poured into a beaker, and 25.0 mL of Liquid B are poured into an identical beaker. Stirrers in each beaker are connected to motors, and the forces FA and FB needed to stir each liquid at a constant rate are measured. predicted outcome OPA will be greater than PB OPA will be less than PB OPA will be equal to PB It's impossible to predict whether PA or PB will be greater without more information.…arrow_forwardShow work. Don't give Ai generated solutionarrow_forward
- 5. Please draw in the blanks the missing transition states and the correlated products. Explicitly display relevant absolute stereochemical configuration. MeOH I OMe H Endo transition state, dienophile approaching from the bottom of diene + H ཎྞཾ ཌཱརཱ༔,_o OMe H H OMe Endo transition state, dienophile approaching from the top of diene or from the bottom but horizontally flipped (draw one) + Exo transition state, dienophile approaching from the top of diene or from the bottom but horizontally flipped (draw one) Exo transition state, dienophile approaching from the top of diene or from the bottom but horizontally flipped (draw one) MeO H H MeO H MeO H MeO H Harrow_forwardH H (1) H C. C C .H (2) (3) Cl H The ideal value for bond angle (1) is (Choose one) and the ideal value for bond angle (3) is (Choose one) degrees, the value for bond angle (2) is (Choose one) degrees, degrees.arrow_forwardShow work.....don't give Ai generated solutionarrow_forward
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill EducationPrinciples of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
- Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill EducationChemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage LearningElementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY