Architectural Drafting and Design (MindTap Course List)
7th Edition
ISBN: 9781285165738
Author: Alan Jefferis, David A. Madsen, David P. Madsen
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 19, Problem 19.10Q
To determine
The definition of outlet.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Q1/ A reinforced concrete beam has the following properties:
•
Beam width (b) 300 mm
Beam height (h) = 600 mm
•
Effective depth (d)- 525 mm
.
Concrete compressive strength (f'e) - 27 MPa
•
Steel yield strength (fy)=420 MPa
•
Steel reinforcement area (As) 1473 mm²
=
•
Modular ratio (n)=8.2
Calculate the location of the neutral axis and determine if the section is in the uncracked or cracked
stage when subjected to a bending moment of 81 kN m. Use the working stress method.
What is the difference between a GIS and an LIS?
What is the difference between remote and autonomous operation of a sUAS?
Chapter 19 Solutions
Architectural Drafting and Design (MindTap Course List)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- 3. Determine the approximate axial forces, shears, and moments for all the members of the frame shown in Figure 3 using: a) Portal method b) Cantilever method c) SAP2000 80 kN 40 kN G H D E F A B 10 m 10 m C Figure 3. Problem 12.10 of Structural Analysis, 6th Edition, Aslam Kassimali. 6 m 6 marrow_forwardThe answers that was given to me by you earlier were incorrect please help re solvearrow_forward1. A) Determine the reactions and draw the shear and bending moment diagrams for the beam shown in Figure 1 using the method of consistent deformation (beam-deflection formulas attached on the next page). B) After solving the problem manually, compare the results for reactions, shear force, and bending moment diagrams with the analysis from SAP2000 (Attach the SAP2000 file and results as part of your assignment submission). 10 kN/m 30 kN B C A D 4 m 9 m 6 m EI=constant Figure 1. Problem 15.4 of Structural Analysis, 6th Edition, Aslam Kassimali.arrow_forward
- 2. Draw the approximate shear and bending moment diagrams for all the members of the frame shown in Figure 2, and compare the shear force and bending moment results with the analysis from SAP2000. G A 10 kN/m H 10 kN/m Ꭰ E 6 m B C 6 m 4 m F 4 m Figure 2. Problem 12.4 of Structural Analysis, 6th Edition, Aslam Kassimali.arrow_forwardConsider two strata of the same soil material that lie between two channels. The first stratum is confined and the second one is unconfined, and the water surface elevations in the channels are 24 and 16 m above the bottom of the unconfined aquifer. What should be the thickness of the confined aquifer for which 2) the discharge through the confined aquifer is half of that through the unconfined aquifer?arrow_forwardConsider two strata of the same soil material that lie between two channels. The first stratum is confined and the second one is unconfined, and the water surface elevations in the channels are 24 and 16 m above the bottom of the unconfined aquifer. What should be the thickness of the confined aquifer for which 1) the discharge through both strata is equalarrow_forward
- A confined aquifer of 10-m thickness and 16.43 m/day hydraulic conductivity is fully penetrated by a pumping well of 0.5 m radius operating at Q = 425 m3/day. Determine the drawdown (Sw) under steady-state conditions in the pumping well and 50 m away from the well. Take the radius of influence of the pumping as 300 m.arrow_forwardUse the unit load method to compute the horizontal displacement at A. Take E =29,000 ksi. Themoment of inertia of each frame member is shown in the figure. Assume that the support at D is a pinsupport, and a roller support at A. Ignore shear and axial deformations, i.e., assume that thedeformations are due to bending only. Please show the actual steps and calculations/diagrams to solve. The last time I asked this question those were not provided.arrow_forwardA sample of silty sand is tested in cylinder of diameter (10 cm) and the length between the two measuring points is (25 cm) and the head difference is (15 cm), the flow rate is (1.7 cm3/min). Calculate the hydraulic conductivity (K)?arrow_forward
- For the shown figure: determine the hB and the vertical velocity? 2 cm 25 cm B 5 cm C Ground surface hB Water table Piezometric surface Unconfined aquifer (K= 10 m/day) Aquitard (K=0.2 m/day) Leaky aquiferarrow_forwardA leaky confined aquifer is overlain with unconfined aquifer. The estimated recharge rate from the aquifer is 0.085 m/year), the average head in the aquifer is (6.8 m) and the thickness of the aquifer is (4.3 m).calculate the vertical hydraulic conductivity of the aquifer.arrow_forwardA company invested an amount of $85,000 to implement a project, and the expected receipts from this project during the 5 years were as follows: End the year 1 $10,000 | (العائدات) Receipts | 2 $25,000 3 $35,000 $45,000 5 $30,000 Find I.R.R. and determine if the project is desirable or not If the MARR was 16%? Q: An investor bought a factory for an amount of $10 million, the estimated useful life is 40 years and the estimated salvage value is $1 million, the factory's annual revenues are $500,000. Use the Sum years' digits method and Straight line method to find: a) Annual depreciation charge at the end of the 25th year b) Total depreciation charge at the end of the 25th year c) Book value at the end of the 25th yeararrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Architectural Drafting and Design (MindTap Course...Civil EngineeringISBN:9781285165738Author:Alan Jefferis, David A. Madsen, David P. MadsenPublisher:Cengage Learning
Residential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781285852225Author:Gregory W FletcherPublisher:Cengage Learning
Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
Architectural Drafting and Design (MindTap Course...
Civil Engineering
ISBN:9781285165738
Author:Alan Jefferis, David A. Madsen, David P. Madsen
Publisher:Cengage Learning
Residential Construction Academy: House Wiring (M...
Civil Engineering
ISBN:9781285852225
Author:Gregory W Fletcher
Publisher:Cengage Learning
Construction Materials, Methods and Techniques (M...
Civil Engineering
ISBN:9781305086272
Author:William P. Spence, Eva Kultermann
Publisher:Cengage Learning