Terms to which acronyms TIN, DEM, DTM apply.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 18, Problem 18.1P

To determine

Terms to which acronyms TIN, DEM, DTM apply.

Expert Solution & Answer

Explanation of Solution

Terms to which acronyms TIN, DEM, DTM apply are:

TIN− Triangulated Irregular Network - The GIS community has been using triangular irregular networks (TIN) for many years and is a digital means of representing surface morphology. TINs are a form of digital geographical data based on vectors and are built by triangulating a set of vertices (points). The vertices are linked to a series of edges to form a triangle network. There are different methods of interpolation to form these triangles such as Delaunay triangulation or distance ordering. Arc GIS supports the Delaunay triangulation method.

DEM− Digital Elevation Model- The digital elevation model (DEM) is the digital representation and elevation of the land surface in relation to any reference data. DEM is often used to refer to any topographic surface digital representation. DEM is the simplest form of digital topography representation. DEMs are used to determine terrain characteristics such as lift at any point, slope and aspect.

DTM− Digital Terrain Model- A Digital Terrain Model (DTM) is a DEM in which terrain data has been further enhanced with break lines, creating greater accuracy as it contains additional information defining terrain in areas where Lidar data alone is unable to do the job effectively.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

Calculate internal moments at D and E for beam CDE showing all working. Assume the support at A is a roller and B is a pin. There are fixed connected joints at D and E. Assume P equals 9.6 and w equals 0.36

Determine the heel and toe stresses and the factor of safeties for sliding and overturning for the gravity dam section shown in the figure below for the following loading conditions: - - - - - Horizontal earthquake (Kh) = 0.1 Normal uplift pressure with gallery drain working Silt deposit up to 30 m height No wave pressure and no ice pressure Unit weight of concrete = 2.4 Ton/m³ and unit weight of silty water = 1.4 Ton/m³ - Submerged weight of silt = 0.9 Ton/m³ - Coefficient of friction = 0.65 and angle of repose = 25° Solve this question with the presence of gallery and without gallery., discuss the issue in both cases.... 144 m 4m 8m 6m Wi 8m +7m. 120m

Studies have shown that the traffic flow on a two-lane road adjacent to a school can be described by the Greenshields model. A length of 0.5 mi adjacent to a school is described as a school zone (see the figure) and operates for a period of 30 min just before the start of school and just after the close of school. The posted speed limit for the school zone during its operation is 15 mi/h. Data collected at the site when the school zone is not in operation show that the jam density and mean free speed for each lane are 136 veh/mi and 63 mi/h. If the demand flow on the highway at the times of operation of the school zone is 90% of the capacity of the highway, determine the following. 0.5 mile School Zone (a) the velocity of the shock wave created by the operation of the school zone (Enter the velocity of the backward forming shock wave in mi/h. Indicate the direction with the sign of your answer.) mi/h (b) the number of vehicles affected by the school zone during this 30-minute operation…

Answer 2

Question

Chapter 18, Problem 18.1P

To determine

Terms to which acronyms TIN, DEM, DTM apply.

Expert Solution & Answer

Explanation of Solution

Terms to which acronyms TIN, DEM, DTM apply are:

TIN− Triangulated Irregular Network - The GIS community has been using triangular irregular networks (TIN) for many years and is a digital means of representing surface morphology. TINs are a form of digital geographical data based on vectors and are built by triangulating a set of vertices (points). The vertices are linked to a series of edges to form a triangle network. There are different methods of interpolation to form these triangles such as Delaunay triangulation or distance ordering. Arc GIS supports the Delaunay triangulation method.

DEM− Digital Elevation Model- The digital elevation model (DEM) is the digital representation and elevation of the land surface in relation to any reference data. DEM is often used to refer to any topographic surface digital representation. DEM is the simplest form of digital topography representation. DEMs are used to determine terrain characteristics such as lift at any point, slope and aspect.

DTM− Digital Terrain Model- A Digital Terrain Model (DTM) is a DEM in which terrain data has been further enhanced with break lines, creating greater accuracy as it contains additional information defining terrain in areas where Lidar data alone is unable to do the job effectively.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 18, Problem 18.1P

To determine

Terms to which acronyms TIN, DEM, DTM apply.

Expert Solution & Answer

Explanation of Solution

Terms to which acronyms TIN, DEM, DTM apply are:

TIN− Triangulated Irregular Network - The GIS community has been using triangular irregular networks (TIN) for many years and is a digital means of representing surface morphology. TINs are a form of digital geographical data based on vectors and are built by triangulating a set of vertices (points). The vertices are linked to a series of edges to form a triangle network. There are different methods of interpolation to form these triangles such as Delaunay triangulation or distance ordering. Arc GIS supports the Delaunay triangulation method.

DEM− Digital Elevation Model- The digital elevation model (DEM) is the digital representation and elevation of the land surface in relation to any reference data. DEM is often used to refer to any topographic surface digital representation. DEM is the simplest form of digital topography representation. DEMs are used to determine terrain characteristics such as lift at any point, slope and aspect.

DTM− Digital Terrain Model- A Digital Terrain Model (DTM) is a DEM in which terrain data has been further enhanced with break lines, creating greater accuracy as it contains additional information defining terrain in areas where Lidar data alone is unable to do the job effectively.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 18, Problem 18.1P

To determine

Terms to which acronyms TIN, DEM, DTM apply.

Expert Solution & Answer

Explanation of Solution

Terms to which acronyms TIN, DEM, DTM apply are:

TIN− Triangulated Irregular Network - The GIS community has been using triangular irregular networks (TIN) for many years and is a digital means of representing surface morphology. TINs are a form of digital geographical data based on vectors and are built by triangulating a set of vertices (points). The vertices are linked to a series of edges to form a triangle network. There are different methods of interpolation to form these triangles such as Delaunay triangulation or distance ordering. Arc GIS supports the Delaunay triangulation method.

DEM− Digital Elevation Model- The digital elevation model (DEM) is the digital representation and elevation of the land surface in relation to any reference data. DEM is often used to refer to any topographic surface digital representation. DEM is the simplest form of digital topography representation. DEMs are used to determine terrain characteristics such as lift at any point, slope and aspect.

DTM− Digital Terrain Model- A Digital Terrain Model (DTM) is a DEM in which terrain data has been further enhanced with break lines, creating greater accuracy as it contains additional information defining terrain in areas where Lidar data alone is unable to do the job effectively.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 18, Problem 18.1P

To determine

Terms to which acronyms TIN, DEM, DTM apply.

Expert Solution & Answer

Explanation of Solution

Terms to which acronyms TIN, DEM, DTM apply are:

TIN− Triangulated Irregular Network - The GIS community has been using triangular irregular networks (TIN) for many years and is a digital means of representing surface morphology. TINs are a form of digital geographical data based on vectors and are built by triangulating a set of vertices (points). The vertices are linked to a series of edges to form a triangle network. There are different methods of interpolation to form these triangles such as Delaunay triangulation or distance ordering. Arc GIS supports the Delaunay triangulation method.

DEM− Digital Elevation Model- The digital elevation model (DEM) is the digital representation and elevation of the land surface in relation to any reference data. DEM is often used to refer to any topographic surface digital representation. DEM is the simplest form of digital topography representation. DEMs are used to determine terrain characteristics such as lift at any point, slope and aspect.

DTM− Digital Terrain Model- A Digital Terrain Model (DTM) is a DEM in which terrain data has been further enhanced with break lines, creating greater accuracy as it contains additional information defining terrain in areas where Lidar data alone is unable to do the job effectively.

Answer 6

Chapter 18, Problem 18.1P

To determine

Terms to which acronyms TIN, DEM, DTM apply.

Expert Solution & Answer

Explanation of Solution

Terms to which acronyms TIN, DEM, DTM apply are:

TIN− Triangulated Irregular Network - The GIS community has been using triangular irregular networks (TIN) for many years and is a digital means of representing surface morphology. TINs are a form of digital geographical data based on vectors and are built by triangulating a set of vertices (points). The vertices are linked to a series of edges to form a triangle network. There are different methods of interpolation to form these triangles such as Delaunay triangulation or distance ordering. Arc GIS supports the Delaunay triangulation method.

DEM− Digital Elevation Model- The digital elevation model (DEM) is the digital representation and elevation of the land surface in relation to any reference data. DEM is often used to refer to any topographic surface digital representation. DEM is the simplest form of digital topography representation. DEMs are used to determine terrain characteristics such as lift at any point, slope and aspect.

DTM− Digital Terrain Model- A Digital Terrain Model (DTM) is a DEM in which terrain data has been further enhanced with break lines, creating greater accuracy as it contains additional information defining terrain in areas where Lidar data alone is unable to do the job effectively.

Answer 7

Chapter 18, Problem 18.1P

To determine

Terms to which acronyms TIN, DEM, DTM apply.

Answer 8

Expert Solution & Answer

Explanation of Solution

Terms to which acronyms TIN, DEM, DTM apply are:

TIN− Triangulated Irregular Network - The GIS community has been using triangular irregular networks (TIN) for many years and is a digital means of representing surface morphology. TINs are a form of digital geographical data based on vectors and are built by triangulating a set of vertices (points). The vertices are linked to a series of edges to form a triangle network. There are different methods of interpolation to form these triangles such as Delaunay triangulation or distance ordering. Arc GIS supports the Delaunay triangulation method.

DEM− Digital Elevation Model- The digital elevation model (DEM) is the digital representation and elevation of the land surface in relation to any reference data. DEM is often used to refer to any topographic surface digital representation. DEM is the simplest form of digital topography representation. DEMs are used to determine terrain characteristics such as lift at any point, slope and aspect.

DTM− Digital Terrain Model- A Digital Terrain Model (DTM) is a DEM in which terrain data has been further enhanced with break lines, creating greater accuracy as it contains additional information defining terrain in areas where Lidar data alone is unable to do the job effectively.