Explanation Write equation of the molar mass of the mixture of oxygen and nitrogen. M m = y O 2 M O 2 + y N 2 M N 2 (I) Here, the molar mass of the mixture is M m , the molar mass of the oxygen is M O 2 , molar mass of nitrogen is M N 2 , number of moles of oxygen is y O 2 , and number of moles of nitrogen is y N 2 . Refer Table A-1, “Molar mass, gas constant, and critical-point properties”, obtain the following properties. The molar mass of oxygen ( M O 2 ) is 31.999 kg/kmol ≃ 32 kg/kmol . The molar mass of nitrogen ( M N 2 ) is 28.013 kg/kmol ≃ 28 kg/kmol . Refer Table A-2, “Ideal-gas specific heats of various common gases”, obtain the following properties. The specific heat ratio ( k ) of oxygen is 1.395 ≃ 1.4 . The specific heat ratio ( k ) of nitrogen is 1.4 . Here, the specific heat ratios of oxygen and nitrogen are equal. Hence, the ratios of critical temperature, pressure, density to stagnation temperature, pressure, and density are expressed as follows. Write the formula for the critical temperature of the mixture. T ∗ = T 0 ( 2 k + 1 ) (II) Here, the critical temperature of mixture is T ∗ , the ratio of specific heats is k , and stagnation temperature of mixture is T 0 . Write the formula for the critical pressure of the mixture. P ∗ = P 0 ( 2 k + 1 ) k / ( k − 1 ) (III) Here, the critical pressure of mixture is P ∗ , and the stagnation pressure of mixture is P 0 . Write the formula for the critical density. ρ ∗ = P ∗ R m T ∗ (IV) Here, the critical density of mixture is ρ ∗ , and the gas constant of mixture is R m . The gas constant of mixture ( R m ) is expressed as follows. R m = R u M m (V) Here, the universal gas constant is R u . Refer Table A-1, “Molar mass, gas constant, and critical-point properties”. The universal gas constant ( R u ) is 8.314 kJ/kmol ⋅ K . Conclusion: It is given that the molar mixture is equivalent. Hence, the number of moles of oxygen and nitrogen are as follows. y O 2 = 0.5 y N 2 = 0.5 Substitute 0.5 for y O 2 , 0.5 for y N 2 , 32 kg/kmol for M O 2 , and 28 kg/kmol for M N 2 in Equation (I)

9th Edition

ISBN: 8220106796979

Author: CENGEL

Publisher: YUZU

See similar textbooks

Concept explainers

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the d…

Videos

Question

Chapter 17.7, Problem 129RP

To determine

The critical temperature, pressure, and density for stagnation and pressure of 550 K and 350 kPa for the equimolar mixture of oxygen and nitrogen.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 17.7, Problem 128RP

Chapter 17.7, Problem 130RP

Students have asked these similar questions

(9) Figure Q9 shows a 2 m long symmetric I beam where the upper and lower sections are 2X wide and the middle section is X wide, where X is 49 mm. The I beam sections are all Y=48 mm in depth. The beam is loaded in the middle with a load of Z=59 kN causing reaction forces at either end of the beam's supports. What is the maximum (positive) bending stress experienced in the beam in terms of mega-Pascals? State your answer to the nearest whole number. Z KN Y mm Y mm Y mm X mm 2X mm Figure Q9 2 m

step by step

Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it carefully and give your own answer. You can borrow ideas from gpt, but please do not believe its answer.Very very grateful! Please do not copy other's work,i will be very very grateful!!

Chapter 17 Solutions

EBK THERMODYNAMICS: AN ENGINEERING APPR

Ch. 17.7 - A high-speed aircraft is cruising in still air....Ch. 17.7 - What is dynamic temperature?Ch. 17.7 - Prob. 3P Ch. 17.7 - Prob. 4P Ch. 17.7 - Prob. 5P Ch. 17.7 - Prob. 6P Ch. 17.7 - Calculate the stagnation temperature and pressure...Ch. 17.7 - Prob. 8P Ch. 17.7 - Prob. 9P Ch. 17.7 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The critical temperature, pressure, and density for stagnation and pressure of 550 K and 350 kPa for the equimolar mixture of oxygen and nitrogen.

Solution Summary: The author explains the critical temperature, pressure, and density for the equimolar mixture of oxygen and nitrogen.

Concept explainers

Videos

The critical temperature, pressure, and density for stagnation and pressure of 550 K and 350 kPa for the equimolar mixture of oxygen and nitrogen.

Want to see the full answer?

Chapter 17 Solutions