THERMODYNAMICS: ENG APPROACH LOOSELEAF
THERMODYNAMICS: ENG APPROACH LOOSELEAF
9th Edition
ISBN: 9781266084584
Author: CENGEL
Publisher: MCG
bartleby

Videos

Question
100%
Book Icon
Chapter 15.7, Problem 62P
To determine

The heat transfer of fuel in the boiler.

Expert Solution & Answer
Check Mark

Answer to Problem 62P

The heat transfer of fuel in the boiler is 23,022kJ/kgfuel.

Explanation of Solution

Express the number of moles of carbon.

NC=mfCMC (I)

Here, molar mass of carbon is MC and mole fraction of carbon is mfC.

Express the number of moles of hydrogen.

NH2=mfH2MH2 (II)

Here, molar mass of hydrogen is MH2 and mole fraction of hydrogen is mfH2.

Express the number of moles of oxygen.

NO2=mfO2MO2 (III)

Here, molar mass of oxygen is MO2 and mole fraction of oxygen is mfO2.

Express the number of moles of nitrogen.

NN2=mfN2MN2 (IV)

Here, molar mass of nitrogen is MN2 and mole fraction of nitrogen is mfN2.

Express the number of moles of sulfur.

NS=mfSMS (V)

Here, molar mass of sulphur is MS and mole fraction of sulfur is mfS.

Express the total number of moles.

Nm=NC+NH2+NO2+NN2+NS (VI)

Here, number of moles of carbon, hydrogen, oxygen, nitrogen and sulfur is NC, NH2, NO2, NN2 and NS respectively.

Express the mole fraction of carbon.

yC=NCNm (VII)

Express the mole fraction of hydrogen.

yH2=NH2Nm (VIII)

Express the mole fraction of oxygen.

yO2=NO2Nm (IX)

Express the mole fraction of nitrogen.

yN2=NN2Nm (X)

Express the mole fraction of sulfur.

yS=NSNm (XI)

Express the heat transfer from the combustion chamber.

Q¯out=NP(h¯fo+h¯h¯o)PNR(h¯fo+h¯h¯o)R=NP(h¯fo+h¯400Kh¯298Ko)PNR(h¯fo+h¯400Kh¯298Ko)R (XII)

Here, number of moles of products is NP, number of moles of reactants is NR, enthalpy of formation is h¯f.

Express the enthalpy change of sulfur dioxide between the standard temperature and the product temperature.

Δh¯SO2=cpΔT=cp(T2Tstand) (XIII)

Here, specific heat constant pressure is cp net temperature is ΔT, temperature at state 2 is T2 and temperature at standard condition is Tstand.

Express the heat transfer of fuel in the boiler.

Qout=Q¯outNCMC+NH2MH2+NO2MO2+NN2MN2+NSMS (XIV)

Here, number of moles of carbon, hydrogen, oxygen, nitrogen and sulfur is MC,MH2, MO2, MN2andMS respectively.

Conclusion:

Refer Table A-1, “molar mass, gas constant, and the critical point properties”, and write the molar masses.

MC=12kg/kmolMH2=2kg/kmolMO2=32kg/kmolMS=32kg/kmol

MN2=28kg/kmol

Substitute 39.25kg for mC and 12kg/kmol for MC in Equation (I).

NC=39.25kg12kg/kmol=3.271kmol

Substitute 6.93kg for mH2 and 2kg/kmol for MH2 in Equation (II).

NH2=6.93kg2kg/kmol=3.465kmol

Substitute 41.11kg for mO2 and 32kg/kmol for MO2 in Equation (III).

NO2=41.11kg32kg/kmol=1.285kmol

Substitute 0.72kg for mN2 and 28kg/kmol for MN2 in Equation (IV).

NN2=0.72kg28kg/kmol=0.0257kmol

Substitute 0.79kg for mS and 32kg/kmol for MS in Equation (V).

NS=0.79kg32kg/kmol=0.0247kmol

Substitute 3.271kmol for NC, 3.465kmol for NH2, 1.285kmol for NO2, 0.0257kmol for NN2 and 0.00247kmol for NS in Equation (VI).

Nm=3.271kmol+3.465kmol+1.285kmol+0.0257kmol+0.0247kmol=8.071kmol

Substitute 3.271kmol for NC and 8.071kmol for Nm in Equation (VII).

yC=3.271kmol8.071kmol=0.4052

Substitute 3.465kmol for NH2 and 8.071kmol for Nm in Equation (VIII).

yH2=3.465kmol8.071kmol=0.4293

Substitute 1.285kmol for NO2 and 8.071kmol for Nm in Equation (IX).

yO2=1.285kmol8.071kmol=0.1592

Substitute 0.0257kmol for NN2 and 8.071kmol for Nm in Equation (X).

yN2=0.0257kmol8.071kmol=0.00319

Substitute 0.0247kmol for NS and 8.071kmol for Nm in Equation (XI).

yS=0.0247kmol8.071kmol=0.00306

Express the combustion equation.

[{0.4052C+0.4293H2+0.1592O2+0.00319N2+0.00306S+1.4ath(O2+3.76N2)}{0.4052CO2+0.4293H2O+0.4athO2+0.00306SO2+1.4ath×3.76N2}] (XV)

Here, stoichiometric coefficient of air is ath, oxygen is O2, nitrogen is N2, carbon dioxide is CO2, water is H2O and hydrogen is H2.

Express the stoichiometric coefficient of air by O2 balancing.

0.1592+1.4ath=0.4052+0.5×0.4293+0.4ath+0.00306ath=0.4637

Substitute 0.4637 for ath in Equation (XV).

[{0.4052C+0.4293H2+0.1592O2+0.00319N2+0.00306S+1.4×0.4637(O2+3.76N2)}{0.4052CO2+0.4293H2O+0.4×0.4637O2+0.00306SO2+1.4×0.4637×3.76N2}][{0.4052C+0.4293H2+0.1592O2+0.00319N2+0.00306S+0.6492(O2+3.76N2)}{0.4052CO2+0.4293H2O+0.1855O2+0.00306SO2+2.441N2}] (XVI)

Refer Equation (XVI) and write the number of moles of reactants.

MC=0.4052kmolMH2=0.4293kmolMO2=0.15920kmol

MN2=0.00319kmolMS=0.00306kmol

Perform unit conversion of temperature at state 2 from degree Celsius to Kelvin.

T2=127°C=(127+273)K=400K

Refer Equation (XVI), and write the number of moles of products.

NP,CO2=0.4052kmolNP,H2O=0.4293kmolNP,O2=0.1855kmolNP,SO2=0.00306kmol

NP,N2=2.441kmol

Here, number of moles of product carbon dioxide, water, oxygen, sulfur dioxide and nitrogen is NP,CO2,NP,H2O,NP,O2,NP,SO2andNP,N2 respectively.

Take the temperature at standard condition as,

Tstand=25°C

Substitute 41.7kJ/kmolK for cp and 127°C for T2 and 25°C for Tstand in Equation (XIII).

Δh¯SO2=(41.7kJ/kmolK)(127°C25°C)=(41.7kJ/kmolK)[(12725)K]=4253kJ/kmol

Refer Appendix Table A-18, A-19, A-20, A-23 and A-26 and write the property table for products and reactants as in Table (1).

Substance

hfo¯

(kJ/kmol)

h¯298K

(kJ/kmol)

h¯400K

(kJ/kmol)

O20868211,711
N20866911,640
H2O(g)241,820990413,356
CO2393,520936413,372
SO2297,100  

Substitute the values form Table (I) into Equation (XII) to get,

Q¯out={[(0.4052)(393,520+13,3729364)]+[(04293)(241,820+13,3569904)]+[(0.1855)(0+11,7118682)]+[(2.441)(0+11,6408669)]+[(0.00306)(297,100+42530)]}=253,244kJ/kmolfuelQ¯out=253,244kJ/kmolfuel

Substitute 253,244kJ/kmolfuel for Q¯out, 0.4052kmol for MC, 0.4293kmol for MH2, 0.15920kmol for MO2, 0.00319kmol for MN2, 0.00306kmol for MS, 12kg/kmol for MC, 2kg/kmol for MH2, 32kg/kmol for MO2, 28kg/kmol for MN2 and 32kg/kmol for MS in Equation (XIV).

Qout=253,244kJ/kmolfuel[(0.4052×12)+(0.4293×2)+(0.1592×32)+(0.00319×28)+(0.00306×32)]kg/kmol=253,244kJ/kmolfuel11kg/kmol=23,022kJ/kgfuel

Hence, the heat transfer of fuel in the boiler is 23,022kJ/kgfuel.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine: a) the minimum permissible diameter for aluminum shafts (1) and (2) b) the minimum permissible diameter for steel shaft (3). c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).
First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³
2/Y Y+1 2Cp Q1/ Show that Cda Az x P1 mactual Cdf Af R/T₁ 2pf(P1-P2-zxgxpf) Q2/ A simple jet carburetor has to supply 5 Kg of air per minute. The air is at a pressure of 1.013 bar and a temperature of 27 °C. Calculate the throat diameter of the choke for air flow velocity of 90 m/sec. Take velocity coefficient to be 0.8. Assume isentropic flow and the flow to be compressible. Quiz/ Determine the air-fuel ratio supplied at 5000 m altitude by a carburetor which is adjusted to give an air-fuel ratio of 14:1 at sea level where air temperature is 27 °C and pressure is 1.013 bar. The temperature of air decreases with altitude as given by the expression The air pressure decreases with altitude as per relation h = 19200 log10 (1.013), where P is in bar. State any assumptions made. t = ts P 0.0065h

Chapter 15 Solutions

THERMODYNAMICS: ENG APPROACH LOOSELEAF

Ch. 15.7 - What does 100 percent theoretical air represent?Ch. 15.7 - Consider a fuel that is burned with (a) 130...Ch. 15.7 - What are the causes of incomplete combustion?Ch. 15.7 - Which is more likely to be found in the products...Ch. 15.7 - Methane (CH4) is burned with the stoichiometric...Ch. 15.7 - Prob. 16PCh. 15.7 - n-Butane fuel (C4H10) is burned with the...Ch. 15.7 - Prob. 18PCh. 15.7 - Propane (C3H8) is burned with 75 percent excess...Ch. 15.7 - Propane fuel (C3H8) is burned with 30 percent...Ch. 15.7 - In a combustion chamber, ethane (C2H6) is burned...Ch. 15.7 - Prob. 22PCh. 15.7 - Prob. 23PCh. 15.7 - Ethane (C2H6) is burned with 20 percent excess air...Ch. 15.7 - Octane (C8H18) is burned with 250 percent...Ch. 15.7 - Prob. 26PCh. 15.7 - A fuel mixture of 60 percent by mass methane (CH4)...Ch. 15.7 - Prob. 28PCh. 15.7 - A certain natural gas has the following volumetric...Ch. 15.7 - Prob. 30PCh. 15.7 - A gaseous fuel with a volumetric analysis of 45...Ch. 15.7 - Prob. 33PCh. 15.7 - The fuel mixer in a natural gas burner mixes...Ch. 15.7 - Prob. 35PCh. 15.7 - Prob. 36PCh. 15.7 - Determine the fuelair ratio when coal from...Ch. 15.7 - Prob. 38PCh. 15.7 - Prob. 39PCh. 15.7 - Prob. 40PCh. 15.7 - Prob. 41PCh. 15.7 - When are the enthalpy of formation and the...Ch. 15.7 - Prob. 43PCh. 15.7 - Prob. 44PCh. 15.7 - Prob. 45PCh. 15.7 - Prob. 46PCh. 15.7 - Prob. 48PCh. 15.7 - Repeat Prob. 1546 for liquid octane (C8H18).Ch. 15.7 - Ethane (C2H6) is burned at atmospheric pressure...Ch. 15.7 - Reconsider Prob. 1550. What minimum pressure of...Ch. 15.7 - Calculate the HHV and LHV of gaseous n-octane fuel...Ch. 15.7 - Prob. 53PCh. 15.7 - Consider a complete combustion process during...Ch. 15.7 - Prob. 56PCh. 15.7 - Prob. 57PCh. 15.7 - Prob. 58PCh. 15.7 - Propane fuel (C3H8) is burned with an airfuel...Ch. 15.7 - Prob. 60PCh. 15.7 - Prob. 61PCh. 15.7 - Prob. 62PCh. 15.7 - Octane gas (C8H18) at 25C is burned steadily with...Ch. 15.7 - Liquid ethyl alcohol [C2H5OH(l)] at 25C is burned...Ch. 15.7 - Prob. 66PCh. 15.7 - A gaseous fuel mixture that is 40 percent propane...Ch. 15.7 - A constant-volume tank contains a mixture of 120 g...Ch. 15.7 - Prob. 70PCh. 15.7 - Prob. 71PCh. 15.7 - Prob. 72PCh. 15.7 - A fuel is completely burned first with the...Ch. 15.7 - Prob. 74PCh. 15.7 - Prob. 75PCh. 15.7 - What is the adiabatic flame temperature of methane...Ch. 15.7 - Octane gas (C8H18) at 25C is burned steadily with...Ch. 15.7 - Acetylene gas (C2H2) at 25C is burned during a...Ch. 15.7 - Ethyl alcohol [C2H5OH(g)] is burned with 200...Ch. 15.7 - Prob. 81PCh. 15.7 - Prob. 82PCh. 15.7 - Reconsider Prob. 1582. The combustion products are...Ch. 15.7 - Express the increase of entropy principle for...Ch. 15.7 - Prob. 85PCh. 15.7 - What does the Gibbs function of formation gf of a...Ch. 15.7 - Liquid octane (C8H18) enters a steady-flow...Ch. 15.7 - Prob. 88PCh. 15.7 - Reconsider Prob. 1588. The automobile engine is to...Ch. 15.7 - Benzene gas (C6H6) at 1 atm and 77F is burned...Ch. 15.7 - Prob. 91PCh. 15.7 - n-Octane [C8H18(l)] is burned in the...Ch. 15.7 - A steady-flow combustion chamber is supplied with...Ch. 15.7 - Prob. 94RPCh. 15.7 - Prob. 95RPCh. 15.7 - Prob. 96RPCh. 15.7 - Prob. 97RPCh. 15.7 - Prob. 98RPCh. 15.7 - Prob. 99RPCh. 15.7 - n-Butane (C4H10) is burned with the stoichiometric...Ch. 15.7 - A gaseous fuel mixture of 60 percent propane...Ch. 15.7 - Calculate the higher and lower heating values of...Ch. 15.7 - Prob. 103RPCh. 15.7 - Methane gas (CH4) at 25C is burned steadily with...Ch. 15.7 - A 6-m3 rigid tank initially contains a mixture of...Ch. 15.7 - Propane gas (C3H8) enters a steady-flow combustion...Ch. 15.7 - Determine the highest possible temperature that...Ch. 15.7 - Liquid propane [C3H8(l)] enters a combustion...Ch. 15.7 - Prob. 109RPCh. 15.7 - Prob. 110RPCh. 15.7 - Prob. 111RPCh. 15.7 - A steam boiler heats liquid water at 200C to...Ch. 15.7 - Repeat Prob. 15112 using a coal from Utah that has...Ch. 15.7 - Liquid octane (C8H18) enters a steady-flow...Ch. 15.7 - Prob. 115RPCh. 15.7 - Consider the combustion of a mixture of an...Ch. 15.7 - Prob. 117RPCh. 15.7 - A fuel is burned steadily in a combustion chamber....Ch. 15.7 - A fuel is burned with 70 percent theoretical air....Ch. 15.7 - Prob. 126FEPCh. 15.7 - One kmol of methane (CH4) is burned with an...Ch. 15.7 - The higher heating value of a hydrocarbon fuel...Ch. 15.7 - Acetylene gas (C2H2) is burned completely during a...Ch. 15.7 - An equimolar mixture of carbon dioxide and water...Ch. 15.7 - A fuel is burned during a steady-flow combustion...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Power Plant Explained | Working Principles; Author: RealPars;https://www.youtube.com/watch?v=HGVDu1z5YQ8;License: Standard YouTube License, CC-BY