Fundamentals of Thermal-Fluid Sciences
Fundamentals of Thermal-Fluid Sciences
5th Edition
ISBN: 9780078027680
Author: Yunus A. Cengel Dr., Robert H. Turner, John M. Cimbala
Publisher: McGraw-Hill Education
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 15, Problem 98RQ
To determine

The money wasted per year.

Expert Solution & Answer
Check Mark

Explanation of Solution

Given:

The diameter of the ball is, D=2.62 in.

The equivalent roughness factor is, ε/D=1.5×103.

Distance travelled per year is, L=16000 miles.

Average speed of the car is, V=55 mph.

The overall efficiency is, η=0.308.

The density of the fuel is, ρfuel=50.2lbm/ft3.

The heating value of the fuel is, HV=1.47×107ftlbf/lbm.

Cost of the fuel is $4.00/gal.

Calculation:

Obtain the following properties of air:

  Density,ρair=0.07518lbm/ft3Viscosity,μair=1.227×105lbm/fts

The Reynolds number is,

  Re=ρairVDμair=(0.07518lbm/ft3)(55×1.466ft/s)(2.62/12 ft)1.227×105lbm/fts=107900

The drag coefficient for a sphere for the above Reynolds number is CD=0.505.

The drag force is,

  FD=CDAρairV22=CD(π4D2)ρairV22

The power required to overcome the resistances is,

  W˙drag=FDL=CD(π4D2)ρairV2L2

The energy provided by the fuel is,

  Ereq=W˙dragη=CD(π4D2)ρairV2L2η

The quantity of fuel required is,

  Vfuel=Ereq/HVρfuel=CD(π4D2)ρairV2L2η(HV)ρfuel=(0.505)[π4(2.62/12 ft)2][(0.07518lbm/ft3)×(55×1.466ft/s)2×(16000×5280ft)2]0.308(1.47×107ftlbf/lbm)(50.2lbm/ft3)=0.05343 ft3×7.481 gal1 ft3=0.3997 gal

The extra cost of fuel is,

  Additional Cost=Vfuel×Cost=(0.3997 gal)($4.00/gal)=$1.6

Thus, the money wasted per year is $1.6.

Since the additional cost is minimal, Jamie need not remove the tennis ball.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Given answers to be: i) 14.65 kN; 6.16 kN; 8.46 kN ii) 8.63 kN; 9.88 kN iii) Bearing 6315 for B1 & B2, or Bearing 6215 for B1
(b) A steel 'hot rolled structural hollow section' column of length 5.75 m, has the cross-section shown in Figure Q.5(b) and supports a load of 750 kN. During service, it is subjected to axial compression loading where one end of the column is effectively restrained in position and direction (fixed) and the other is effectively held in position but not in direction (pinned). i) Given that the steel has a design strength of 275 MN/m², determine the load factor for the structural member based upon the BS5950 design approach using Datasheet Q.5(b). [11] ii) Determine the axial load that can be supported by the column using the Rankine-Gordon formula, given that the yield strength of the material is 280 MN/m² and the constant *a* is 1/30000. [6] 300 600 2-300 mm wide x 5 mm thick plates. Figure Q.5(b) L=5.75m Pinned Fixed
Help ارجو مساعدتي في حل هذا السؤال

Chapter 15 Solutions

Fundamentals of Thermal-Fluid Sciences

Ch. 15 - Prob. 11PCh. 15 - What is the difference between skin friction drag...Ch. 15 - Prob. 13PCh. 15 - What is the effect of streamlining on (a) friction...Ch. 15 - What is flow separation? What causes it? What is...Ch. 15 - Prob. 16PCh. 15 - Prob. 17PCh. 15 - Prob. 18PCh. 15 - The resultant of the pressure and wall shear...Ch. 15 - Prob. 20PCh. 15 - Prob. 21PCh. 15 - Prob. 22PCh. 15 - Prob. 24PCh. 15 - Prob. 25PCh. 15 - Prob. 26PCh. 15 - Prob. 27PCh. 15 - A submarine can be treated as an ellipsoid with a...Ch. 15 - Prob. 29PCh. 15 - During major windstorms, high vehicles such as RVs...Ch. 15 - Prob. 31PCh. 15 - Prob. 32PCh. 15 - Prob. 33PCh. 15 - Prob. 34PCh. 15 - Prob. 35PCh. 15 - Prob. 36PCh. 15 - Prob. 37PCh. 15 - Prob. 38PCh. 15 - Prob. 39PCh. 15 - Prob. 40PCh. 15 - Prob. 41PCh. 15 - Prob. 42PCh. 15 - Prob. 43PCh. 15 - Prob. 44PCh. 15 - Prob. 45PCh. 15 - Prob. 46PCh. 15 - Prob. 48PCh. 15 - Prob. 49PCh. 15 - Prob. 51PCh. 15 - Prob. 52PCh. 15 - Prob. 53PCh. 15 - Prob. 54PCh. 15 - Prob. 55PCh. 15 - Prob. 56PCh. 15 - Prob. 57PCh. 15 - Prob. 58PCh. 15 - Prob. 59PCh. 15 - Prob. 60PCh. 15 - Prob. 61PCh. 15 - Prob. 62PCh. 15 - A 2-m-long, 0.2-m-diameter cylindrical pine log...Ch. 15 - Prob. 64PCh. 15 - Prob. 65PCh. 15 - Prob. 66PCh. 15 - Prob. 67PCh. 15 - Prob. 68PCh. 15 - Prob. 69PCh. 15 - Prob. 70PCh. 15 - Prob. 71PCh. 15 - Prob. 72PCh. 15 - What is induced drag on wings? Can induced drag be...Ch. 15 - Prob. 74PCh. 15 - Prob. 75PCh. 15 - Prob. 76PCh. 15 - Prob. 77PCh. 15 - Consider an airplane whose takeoff speed is 220...Ch. 15 - Prob. 79PCh. 15 - Prob. 80PCh. 15 - Prob. 82PCh. 15 - Prob. 83PCh. 15 - Prob. 84PCh. 15 - Prob. 85PCh. 15 - Prob. 86RQCh. 15 - A 1.2-m-external-diameter spherical tank is...Ch. 15 - Prob. 88RQCh. 15 - Prob. 89RQCh. 15 - Prob. 91RQCh. 15 - Prob. 92RQCh. 15 - Prob. 93RQCh. 15 - Prob. 94RQCh. 15 - Prob. 95RQCh. 15 - Prob. 96RQCh. 15 - Prob. 97RQCh. 15 - Prob. 98RQCh. 15 - Prob. 99RQCh. 15 - Prob. 100RQCh. 15 - Prob. 102RQ
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License