AUTOMATIC TRANS...-CLASSRM.+SHOP MANUAL
AUTOMATIC TRANS...-CLASSRM.+SHOP MANUAL
7th Edition
ISBN: 9781337792158
Author: ERJAVEC
Publisher: CENGAGE L
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 15, Problem 8SA

Solve the parallel circuit for total circuit resistance, total circuit amperage, and the amperage through each leg (Figure 15-65).

Chapter 15, Problem 8SA, Solve the parallel circuit for total circuit resistance, total circuit amperage, and the amperage

Expert Solution & Answer
Check Mark
To determine

The total circuit resistance.

Total circuit amperage.

The amperage through leg 1.

The amperage through leg 2.

The amperage through leg 3.

Answer to Problem 8SA

The total circuit resistance is 1Ω.

Total circuit amperage is 12A.

The amperage through leg 1 is 2A.

The amperage through leg2 is 4A.

The amperage through leg3 is 6A.

Explanation of Solution

Given information:

The total voltage is 12V, the first resistance is 6Ω, the second resistance is 3Ω and the third resistance is 2Ω.

Write the expression of total resistance of the circuit.

  1R=1R1+1R2+1R3  ....... (I)

Here, the third resistance is R3, the first resistance is R1 and the second resistance is R2.

Write the expression of total current or amperage.

  I=VR  ....... (II)

Here, the total voltage is V and the total resistance is R.

Write the expression of current or amperage through leg 1.

  I1=VR1  ....... (III)

Write the expression of current or amperage through leg2.

  I2=VR2 ....... (IV)

Write the expression of current or amperage through leg 3.

  I3=VR3  ....... (V)

Calculation:

Substitute 6Ω for R1, 3Ω for R2 and 2Ω for R3 in Equation (I).

  1R=16Ω+13Ω+12Ω1R=1Ω1R=1Ω

Thus, the total circuit resistance is 1Ω.

Substitute 12V for V and 1Ω for R in Equation (II).

  I=12V1Ω=(12V/Ω)×( 1A 1V/Ω )=12A

Thus, total circuit amperage is 12A.

Substitute 12V for V and 6Ω for R1 in Equation (III).

  I1=12V6Ω=(2V/Ω)×( 1A 1V/Ω )=2A

Thus, the amperage through leg 1 is 2A.

Substitute 12V for V and 3Ω for R2 in Equation (IV).

  I2=12V3Ω=(4V/Ω)×( 1A 1V/Ω )=4A

Thus, the amperage through leg2 is 4A.

Substitute 12V for V and 2Ω for R3 in Equation (V).

  I3=12V2Ω=(6V/Ω)×( 1A 1V/Ω )=6A

Thus, the amperage through leg 3 is 6A.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A shaft is loaded in bending and torsion such that Ma = 70 N·m, T₁ = 45 N · m, M = 55 N. m, and T = 35 N m. For the shaft, S₁ = 700 MPa and S = 560 MPa, and a fully corrected endurance limit of S₂ = 210 MPa is assumed. Let K = 2.2 and K = 1.8. With a Se design factor of 2.0 determine the minimum acceptable diameter of the shaft using the a) DE- Goodman b) DE-Morrow c) DE-Gerber d) DE-SWT
The feed flow rate to an adiabatic continuous stirred tank reactor (CSTR) in which an exothermicreaction is occurring is increased from 1000 to 1400. kg/h, causing the outlet temperature to change as shown:a)  Briefly explain on a physical basis why the temperature in this system oscillates after a step increasein the inlet flow rate. Be clear, complete, and concise. c)  You know that this oscillating response cannot be that of two first order processes with real timeconstant acting in series. Assuming the reaction is first order and the CSTR operates with constant holdup,derive the block diagram with all transfer functions indicating how the temperature would respond to the feedflow rate step change (W’(s) as input and T’(s) as output). An intermediate variable in this block diagram willbe the concentration of A in the reactor, represented by CA’(s). d)  A correct result for part c) will include a feedback loop in the block diagram, indicating the responsein T to a change in w is not…
Spur gears Note : Exam is open notes &tables / Answer all questions. Q.1. The press shown for Figure.1 has a rated load of 22 kN. The twin screws have double start Acme threads, a diameter of 50 mm, and a pitch of 6 mm. Coefficients of friction are 0.05 for the threads and 0.08 for the collar bearings. Collar diameters are 90 mm. The gears have an efficiency of 95 percent and a speed ratio of 60:1. A slip clutch, on the motor shaft, prevents overloading. The full-load motor speed is 1720 rev/min. (a) When the motor is turned on, how fast will the press head move? (Vm= , Vser. = ) (5M) (b) What should be the horsepower rating of the motor? (TR=, Tc= Pser. = " Bronze bushings Foot Motor Bearings watt, Pm= watt, Pm= h.p.) (20M) 2['s Fig.1 Worm Collar bearing
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Text book image
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Text book image
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Text book image
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Text book image
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Text book image
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Ch 2 - 2.2.2 Forced Undamped Oscillation; Author: Benjamin Drew;https://www.youtube.com/watch?v=6Tb7Rx-bCWE;License: Standard youtube license