Explanation Method adopted: Castigliano’s theorem. Explanation: Castigliano’s theorem to determine the slope for the beam is as follows: θ = ∫ 0 L M ( ∂ M ∂ M ′ ) d x E I (1) Here, θ is the slope of the tangent θ at a point on the elastic curve is to be determined, M is internal moment in the beam, expressed as a function of x and caused by both the force P and the actual loads on the beam, M ′ is the external moment, E is modulus of elasticity of a member, and I is moment of inertia of the cross-sectional area about the neutral axis. Internal moment in the beam ( M ): Apply external moment M ′ at the point where the slope is to be determined. Determine the reactions: Entire beam: Show the free-body diagram of the entire beam as in Figure 1. Moment about point A : Determine the vertical reaction at point B by taking moment about point A . ∑ M A = 0 w × 2 L × 2 L 2 − B y ( L ) + M ′ = 0 (2) Along the vertical direction: Determine the vertical reaction at point A by resolving the vertical component of forces. ∑ F y = 0 A y + B y − w × 2 L = 0 (3) Along the horizontal direction: Determine the horizontal reaction at point A by resolving the horizontal component of forces. ∑ F x = 0 A x = 0 Show the calculation of values as follows: Solve Equation (2). B y ( L ) = w × 2 L × 2 L 2 − M ′ B y = 2 w L − M ′ L Substitute ( 2 w L − M ′ L ) for B y in Equation (3). A y + 2 w L − M ′ L − 2 w L = 0 A y = M ′ L Region 0 ≤ x < L : Show the free body diagram of the beam for the region 0 ≤ x < L as in Figure 2. Moment about the section: Determine the moment at the section by taking moment about the section. ∑ M x 1 = 0 M 1 + ( w × x 1 × x 1 2 ) = 0 (4) Solve Equation (4). M 1 = − w ( x 1 ) 2 2 Region L < x ≤ 2 L : Show the free body diagram of the beam for the region L < x ≤ 2 L as in Figure 3. Moment about the section: Determine the moment at the section by taking moment about the section. ∑ M x 2 = 0 − M 2 + A y ( x 2 ) − w × x 2 × x 2 2 + M ′ = 0 (5) Substitute M ′ L for A y in Equation (5). − M 2 + M ′ L ( x 2 ) − w ( x 2 ) 2 2 + M ′ = 0 M 2 = − w ( x 2 ) 2 2 + M ′ x 2 L − M ′ Calculation: Tabulate the calculated values as in Table 1

10th Edition

ISBN: 9780134321158

Author: HIBBELER

Publisher: PEARSON

See similar textbooks

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and af…

Videos

Question

Chapter 14.10, Problem 14.141P

To determine

The slope at point A.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.10, Problem 14.140P

Chapter 14.10, Problem 14.142P

Students have asked these similar questions

Hints: Find the closed loop transfer function and then plot the step response for diFerentvalues of K in MATLAB. Show step response plot for different values of K. Auto Controls Show solutions and provide matlab code NO COPIED ANSWERS OR WILL REPORT!!!!

37. The vertical shaft shown in Figure P12-37 is driven at a speed of 600 rpm with 4.0 hp entering through the bevel gear. Each of the two chain sprockets delivers 2.0 hp to the side to drive mixer blades in a chemical reactor vessel. The bevel gear has a diametral pitch of 5, a pitch diameter of 9.000 in, a face width of 1.31 in, and a pressure angle of 20°. Use SAE 4140 OQT 1000 steel for the shaft. See Chapter 10 for the methods for computing the forces on the bevel gear. Figure P12-37: P37-Bevel gear drive with two chain sprockets Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of strength. Homework Problems 12-24, 12-35, and 12-37 from textbook, done in spreadsheet form. Place drawings of the load, shear, and bending moment body diagrams…

35. The double-reduction, helical gear reducer shown in Figure P12-35 transmits 5.0 hp. Shaft 1 is the input, rotating at 1800 rpm and receiving power directly from an electric motor through a flexible coupling. Shaft 2 rotates at 900 rpm. Shaft 3 is the output, rotating at 300 rpm. A chain sprocket is mounted on the output shaft as shown and delivers the power upward. The data for the gears are given in Table 12-5. Each gear has a 1412° normal pressure angle and a 45° helix angle. The combinations of left- and right-hand helixes are arranged so that the axial forces oppose each other on shaft 2 as shown. Use SAE 4140 OQT 1200 for the shafts. Figure P12-35: P35-Double-reduction helical drive Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of…

Chapter 14 Solutions

Mechanics of Materials

Ch. 14.2 - A material is subjected to a general state of...Ch. 14.2 - The strain-energy density for plane stress must be...Ch. 14.2 - The A-36 steel bar consists of two segments, one...Ch. 14.2 - Determine the torsional strain energy in the A992...Ch. 14.2 - Using bolts of the same material and...Ch. 14.2 - If P = 60 kN, determine the total strain energy...Ch. 14.2 - Determine the maximum force P and the...Ch. 14.2 - Determine the torsional strain energy in the A992...Ch. 14.2 - Determine the torsional strain energy in the A-36...Ch. 14.2 - The shaft assembly is fixed at C. The hollow...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The slope at point A .

Solution Summary: The author explains Castigliano's theorem to determine the slope for the beam.

Concept explainers

Videos

The slope at point A.

Want to see the full answer?

Chapter 14 Solutions