
Concept explainers
(a)
The appropriate model to describe the system when balloon is stationary.
(a)

Answer to Problem 33AP
The appropriate model to describe the system is particle in equilibrium.
Explanation of Solution
The mass of the balloon is
If a system remains stationary, the sum of all forces acted on a system in all direction vertical as well as horizontal is equal to zero. This condition is also called is equilibrium condition.
Conclusion:
Therefore, appropriate model to describe the system is particle in equilibrium.
(b)
The force equation for the balloon for this model.
(b)

Answer to Problem 33AP
The force equation for the balloon for this model is
Explanation of Solution
In equilibrium condition, sum of all forces in vertical direction is equal to zero.
Here,
Conclusion:
Therefore, the force equation for the balloon for this model is
(c)
The mass of the string in terms of
(c)

Answer to Problem 33AP
The mass of the string in the terms of
Explanation of Solution
From equation (I),
The buoyant force act on the balloon is equal to the displaced volume of the air by the balloon.
Formula to calculate the buoyant force acting on the balloon is,
Here,
Formula to calculate the weight of the balloon is,
Here,
Formula to calculate the weight of the helium gas is,
Here,
Formula to calculate the weight of the string is,
Here,
Substitute
Formula to calculate the mass of the helium gas is,
Here,
Substitute
Rearrange the above expression for
Conclusion:
Therefore, the mass of the string in terms of
(d)
The mass of the string.
(d)

Answer to Problem 33AP
The mass of the string is
Explanation of Solution
From equation (II),
Substitute
Conclusion:
Therefore, the mass of the string is
(e)
The length
(e)

Answer to Problem 33AP
The length
Explanation of Solution
From equation (II),
The mass of the string of height
Substitute
Substitute
Conclusion:
Therefore, the length
Want to see more full solutions like this?
Chapter 14 Solutions
EBK PHYSICS FOR SCIENTISTS AND ENGINEER
- Part A: kg (a) Water at 20 °C (p = 998.3 and v = 1 × 10-6 m²/s) flows through a galvanised m³ iron pipe (k = 0.15 mm) with a diameter of 25 mm, entering the room at point A and discharging at point C from the fully opened gate valve B at a volumetric flow rate of 0.003 m³/s. Determine the required pressure at A, considering all the losses that occur in the system described in Figure Q1. Loss coefficients for pipe fittings have been provided in Table 1. [25 marks] (b) Due to corrosion within the pipe, the average flow velocity at C is observed to be V2 m/s after 10 years of operation whilst the pressure at A remains the same as determined in (a). Determine the average annual rate of growth of k within the pipe. [15 marks] 4₁ Figure Q1. Pipe system Page 2 25 mmarrow_forwardFor an independent study project, you design an experiment to measure the speed of light. You propose to bounce laser light off a mirror that is 53.5 km due east and have it detected by a light sensor that is 119 m due south of the laser. The first problem is to orient the mirror so that the laser light reflects off the mirror and into the light sensor. (a) Determine the angle that the normal to the mirror should make with respect to due west.(b) Since you can read your protractor only so accurately, the mirror is slightly misaligned and the actual angle between the normal to the mirror and due west exceeds the desired amount by 0.003°. Determine how far south you need to move the light sensor in order to detect the reflected laser light.arrow_forwardA mirror hangs 1.67 m above the floor on a vertical wall. A ray of sunlight, reflected off the mirror, forms a spot on the floor 1.41 m from the wall. Later in the day, the spot has moved to a point 2.50 m from the wall. (a) What is the change in the angle of elevation of the Sun, between the two observations?arrow_forward
- It is not (theta 1i) or (pi/2 - theta 2i)arrow_forwardAssume the helium-neon lasers commonly used in student physics laboratories have power outputs of 0.250 mW. (a) If such a laser beam is projected onto a circular spot 3.40 mm in diameter, what is its intensity (in watts per meter squared)? 27.5 W/m² (b) Find the peak magnetic field strength (in teslas). 8.57e-7 X T (c) Find the peak electric field strength (in volts per meter). 144 V/marrow_forwardIdentify the most likely substancearrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning





