Bundle: Automotive Technology: A Systems Approach, 6th + MindTap Auto Trades, 4 terms (24 months) Printed Access Card
6th Edition
ISBN: 9781305361454
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 14, Problem 1RQ
What is the most efficient way to increase a radiators efficiency?
Expert Solution & Answer
To determine
To increase a radiator’s efficiency the most efficient way that is used.
Answer to Problem 1RQ
The temperature difference between the coolant and air passing through.
Explanation of Solution
The function of a radiator is to transfer heat from the engine to the atmosphere or the air passing through it. There are two types of radiators depending on the flow of coolant inside the radiator, viz. down flow and crossflow radiators. The efficiency of the radiator depends on a number of factors: the area of contact, the temperature difference, and the coolant capacity. The area of the radiator depends on its design and compactness of the engine whereas the difference in temperature depends upon the coolant inside the radiator and the temperature of the cooling air passing through it. The efficiency also depends on the pumping power as higher pumping force to reduce the coolant temperature faster, but it also needs higher energy to run the pump.
Conclusion:
As the area and other design parameters of a radiator depend on various aspects, the efficiency of the radiator depends on the temperature difference between the coolant and air passing through.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
HWS:
1. A round stepped cast iron shaft of diameters d and D with shoulder fillet radius r is
loaded by an axial tensile load P, as shown in the figure below. Compute the value
of P that may be applied to the bar without failure. Given: d = 25 mm, D = 50 mm,
r = 3.75 mm, Sut = 250 MPa, Suc = 380 MPa, N=1.5.
P
2. Make a report about the most effective techniques used by engineers to reduce the
effects of stress concentration.
A conical pivot bearing 150mm in diameter has a cone angle of 120degree . If the shaft supports an axial load of 20kN and the coefficient of friction is 0.03,find the power lost in friction when the shaft rotates at 200r.p.m , assuming 1. Uniform pressure and uniform wear.
Solve step by step
Chapter 14 Solutions
Bundle: Automotive Technology: A Systems Approach, 6th + MindTap Auto Trades, 4 terms (24 months) Printed Access Card
Ch. 14 - What is the most efficient way to increase a...Ch. 14 - True or False? Oil pressure is determined by...Ch. 14 - Describe the simple test used to determine whether...Ch. 14 - Which of the following is a function of the...Ch. 14 - What is ECD and what can result from it?Ch. 14 - True or False? To eliminate the drain of engine...Ch. 14 - For every pound of pressure put on engine coolant,...Ch. 14 - Which is not a typical method of driving the water...Ch. 14 - Which of the following is not an effective way to...Ch. 14 - Explain why a pressure relief valve is needed in...
Ch. 14 - List five problems that can be caused by engine...Ch. 14 - Cooling system hoses should be replaced when they...Ch. 14 - True or False? The presence of air in the cooling...Ch. 14 - Which of the following is not a true statement...Ch. 14 - Describe the procedure for using air bleed valves...Ch. 14 - Technician A uses a feeler gauge and straightedge...Ch. 14 - Technician A says that excessive engine oil...Ch. 14 - While checking for conditions that might cause...Ch. 14 - When installing an oil pump in an engine...Ch. 14 - Technician A says that if the PCV valve or...Ch. 14 - While bleeding air from a cooling system:...Ch. 14 - While diagnosing an engine that overheats after...Ch. 14 - While performing a cooling system service on a...Ch. 14 - While discussing the causes of extreme engine...Ch. 14 - While diagnosing the cause of air bubbles in the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- show the cam profile for a motion of a constant acceleration in the first 0.25 seconds, a constant velocity in the next 0.5 seconds and a constant deceleration in the last 0.25 seconds. total displacement is 8mm.arrow_forwardSolve step by steparrow_forwardAn element in plane stress is subjected to stresses ☐ x, y, and xx (see figure). Using Mohr's circle: a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. b) Show these stresses in an appropriate sketch 12 MPa 27 MPa T 60 MPaarrow_forward
- 5 kN-m A beam with an inverted tee-shaped cross section is subjected to positive bending mo- ments of M₂ = 5 kN-m. The cross-sectional dimensions of the beam are shown below. 10 mm Determine: (a) the centroid location, the moment of inertia about the z axis, 40 mm 5 kN-m K 150 mm H 15 mm 120 mm (b) the bending stress at points H and K. ans: 17.83mPa (c) the maximum bending stress produced in the cross section.arrow_forwardEXAMPLE 6.4 Draw the shear and moment diagrams for the beam shown in Fig. 6-7a. 15 kN 80 kN·m -5 m B -5 m (a) 5 kN/m Darrow_forward2) A short rectangular post supports compressive loads of P- 175 kN and Q-90 kN, as shown in the figure below. A top view of the post showing the locations where loads P and Q are applied to the top of the post is also given. Determine the vertical normal stresses at corners a, b, c, and d of the post. P=175 kN Q=90 kN 160 mm 120 mm b 40 mm 160 mm a x d 60 mm 40 mmarrow_forward
- For the beam shown below: Find the equation for the shear force as function of x, V(x), along the x domains A-B (0 ≤ x ≤ 5 m) and B-C (5 m sxs 10 m), and draw the shear diagram for the beam. For each step, draw the associated free body diagram and indicate the equations of equilibrium used. Upload your answers in PDF. 2.5 m 15 kN 5 kN/m 80 kN·m Upload your D B 5m- ―5 marrow_forwardQ What is Theories of Brittle failure? Q, what do you mean for each of what's Coming? utں وہی رہیں > Tyiled , Puc > Sut, So, KP, Kt, q When to use this law. N= Out Ouc * Ouc 1 -Out (01+0₂) I'm a mechanical engineering student. I don't understand What is the difference ductile materials. between Brittle andarrow_forwardQ2. (30 Marks) For the following figure: 1. Read the tolerances (GD&T) from the figure? 2. Write the Opitz code (5 digits only) for this product? 3. Write few points about point cloud? And how it can be used to inspect the geometry of products? 4. Draw sketch (free hand) to the top view of the figure below? (()) 5. For the symbol below the figure, what does it means? () will jo الهندسي 08±0.01 A 020±0.01 00.02MAM BM 010±0.01 00.02MAM ماذا يعني هذا Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Understanding Thermal Radiation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=FDmYCI_xYlA;License: Standard youtube license