Concept explainers
(a)
The mass of the gas treating it as an ideal gas mixture.
(a)
Answer to Problem 41P
The mass of the gas treating it as an ideal gas mixture is
Explanation of Solution
Write the expression to calculate the mole number of the substance
Here, the mass of the substance is
Write the expression to calculate the mole fraction of the substance
Here, total mole number of the products is
Write the expression to calculate the individual gas constant
Here, universal gas constant is
Write the expression to calculate the mass of the gas from ideal gas expression.
Here, pressure of the gas is
Conclusion:
From the Table A-1 of “Molar mass, gas constant, and critical-point properties”, obtain the molar masses as follows:
Substitute
Substitute
Calculate the total number of moles
Substitute
Substitute
Substitute
Substitute
Substitute
Thus, the mass of the gas treating it as an ideal gas mixture is
(b)
The mass of the gas using the compressibility chart.
(b)
Answer to Problem 41P
The mass of the gas using the compressibility chart is
Explanation of Solution
Write the expression to calculate the reduced pressure
Here, pressure at the critical point is
Write the expression to calculate the reduced temperature
Here, temperature at the critical point is
Write the expression to calculate the compressibility factor of the mixture
Here, compressibility factor for
Write the expression to calculate the mass from using the compressibility factor.
Conclusion:
Substitute
Substitute
From the Table A-15 of “Nelson-Obert generalized compressibility chart”, obtain the compressibility factor at reduced pressure of 2.972 and reduced temperature of 2.210 as 0.98
Substitute
Substitute
From the Table A-15 of “Nelson-Obert generalized compressibility chart”, obtain the compressibility factor at reduced pressure of 2.119 and reduced temperature of 1.382 as 0.77
Substitute
Substitute
Thus, the mass of the gas using the compressibility chart is
(c)
The mass of the gas using Dalton’ law.
(c)
Answer to Problem 41P
The mass of the gas using the Daltonls law is
Explanation of Solution
Write the expression to calculate the reduced volume specific volume
Conclusion:
From the Table A-2E of “Ideal gas specific heats of various common gases”, obtain the gas constants as follows:
Substitute
From the Table A-15 of “Nelson-Obert generalized compressibility chart”, obtain the compressibility factor at reduced specific volume of 0.8782 and reduced temperature of 2.210 as 0.98
Substitute
From the Table A-15 of “Nelson-Obert generalized compressibility chart”, obtain the compressibility factor at reduced specific volume of 3.244 and reduced temperature of 1.382 as 0.92
Substitute
Substitute
Thus, the mass of the gas using the Daltonls law is
(d)
The mass of the gas using Kay’s rule.
(d)
Answer to Problem 41P
The mass of the gas using Kay’s rule is
Explanation of Solution
Write the formula to calculate the pseudo critical temperature
Write the formula to calculate the pseudo critical pressure
Conclusion:
Substitute
Substitute
Substitute
Substitute
From the Table A-15 of “Nelson-Obert generalized compressibility chart”, obtain the compressibility factor at reduced pressure of 2.949 and reduced temperature of 2.027 as 0.97
Substitute
Thus, the mass of the gas using Kay’s rule is
Want to see more full solutions like this?
Chapter 13 Solutions
EBK THERMODYNAMICS: AN ENGINEERING APPR
- Question 1. A tube rotates in the horizontal ry plane with a constant angular velocity w about the z-axis. A particle of mass m is released from a radial distance R when the tube is in the position shown. This problem is based on problem 3.2 in the text. R m 2R Figure 1 x a) Draw a free body diagram of the particle if the tube is frictionless. b) Draw a free body diagram of the particle if the coefficient of friction between the sides of the tube and the particle is = k = p. c) For the case where the tube is frictionless, what is the radial speed at which the particle leaves the tube? d) For the case where there is friction, derive a differential equation that would allow you to solve for the radius of the particle as a function of time. I'm only looking for the differential equation. DO NOT solve it. 1 e) If there is no friction, what is the angle of the tube when the particle exits? • Hint: You may need to solve a differential equation for the last part. The "potentially useful…arrow_forwardQuestion 2. A smooth uniform sphere of mass m and radius r is squeezed between two massless levers, each of length 1, which are inclined at an angle with the vertical. A mechanism at pivot point O ensures that the angles & remain the same at all times so that the sphere moves straight upward. This problem is based on Problem 3-1 in the text. P P r Figure 2 a) Draw appropriate freebody diagrams of the system assuming that there is no friction. b) Draw appropriate freebody diagrams of the system assuming that there is a coefficient of friction between the sphere and the right lever of μ. c) If a force P is applied between the ends of the levers (shown in the diagram), and there is no friction, what is the acceleration of the sphere when = 30°arrow_forwardIf you had a matrix A = [1 2 3; 4 5 6; 7 8 9] and a matrix B = [1 2 3], how would you cross multiply them i.e. what is the cross product of AxB. what would be the cross product of a dyadic with a vector?arrow_forward
- Problem 3: The inertia matrix can be written in dyadic form which is particularly useful when inertia information is required in various vector bases. On the next page is a right rectangular pyramid of total mass m. Note the location of point Q. (a) Determine the inertia dyadic for the pyramid P, relative to point Q, i.e., 7%, for unit vectors ₁₁, 2, 3.arrow_forwardCan you solve for v? Also, what is A x uarrow_forwardThe external loads on the element shown below at the free end are F = 1.75 kN, P = 9.0 kN, and T = 72 Nm. The tube's outer diameter is 50 mm and the inner diameter is 45 mm. Given: A(the cross-sectional area) is 3.73 cm², Moment inertial I is 10.55 cm4, and J polar moment inertial is 21.1 cm4. Determine the following. (1) The critical element(s) of the bar. (2) Show the state of stress on a stress element for each critical element. -120 mm- Farrow_forward
- A crate weighs 530 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the xy plane. Point A is located at a height of h = 42 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. 2013 Michael Swanbom ↑ Z C BY NC SA b x B у D Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 30 in b 43 in с 4.5 in The tension in rope AB is lb The tension in rope AC is lb The tension in rope AD is lbarrow_forwardThe airplane weighs 144100 lbs and flies at constant speed and trajectory given by 0 on the figure. The plane experiences a drag force of 73620 lbs. a.) If = 11.3°, determine the thrust and lift forces required to maintain this speed and trajectory. b.) Next consider the case where is unknown, but it is known that the lift force is equal to 7.8 times the quantity (Fthrust Fdrag). Compute the resulting trajectory angle - and the lift force in this case. Use the same values for the weight and drag forces as you used for part a. Уллу Fdrag 10. Ө Fthrust cc 10 2013 Michael Swanbom BY NC SA Flift Fweight The lift force acts in the y' direction. The weight acts in the negative y direction. The thrust and drag forces act in the positive and negative x' directions respectively. Part (a) The thrust force is equal to lbs. The lift force is equal to Part (b) The trajectory angle is equal to deg. The lift force is equal to lbs. lbs.arrow_forwardThe hoist consists of a single rope and an arrangement of frictionless pulleys as shown. If the angle 0 = 59°, determine the force that must be applied to the rope, Frope, to lift a load of 4.4 kN. The three-pulley and hook assembly at the center of the system has a mass of 22.5 kg with a center of mass that lies on the line of action of the force applied to the hook. e ΘΕ B CC 10 BY NC SA 2013 Michael Swanbom Fhook Note the figure may not be to scale. Frope = KN HO Fropearrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY