In infrared radiation of 1715cm -1 or of 2800cm -1 , which is higher in energy has to be given. Concept Introduction: Infrared radiation is a type of electromagnetic radiation. The electromagnetic radiation is said to be the energy propagated through free space or a medium in the form of waves. The radiation in infrared region is referred by wave numbers. The wave number is said to be the number of waves per centimetre. The units of wave number is given as units of wavenumber = 1 cm or cm -1

Question

Want to see the full answer?

Answer 1

Question

Chapter 12.3, Problem 12.1P

(a)

Interpretation Introduction

Interpretation:

In infrared radiation of 1715cm-1 or of 2800cm-1, which is higher in energy has to be given.

Concept Introduction:

Infrared radiation is a type of electromagnetic radiation. The electromagnetic radiation is said to be the energy propagated through free space or a medium in the form of waves. The radiation in infrared region is referred by wave numbers.

The wave number is said to be the number of waves per centimetre. The units of wave number is given as

units of wavenumber = 1cm or cm-1

(b)

Interpretation Introduction

Interpretation:

In Radio-frequency radiation of 300MHz or 60MHz, which is higher in energy has to be given.

Concept Introduction:

Radio-frequency radiation is a type of electromagnetic radiation. The electromagnetic radiation is said to be the energy propagated through free space or a medium in the form of waves. The radiation in Radio-frequency region is referred by frequency.

The frequency is said to be the number of waves that pass through a given point at a given time. The units of frequency is described in Hertz (Hz). The units of frequency is given in seconds (s).

frequency = s-1 or 1s

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

I

Draw the anti-Markovnikov product of the hydration of this alkene. this problem. Note for advanced students: draw only one product, and don't worry about showing any stereochemistry. Drawing dash and wedge bonds has been disabled for esc esc ☐ Explanation Check F1 1 2 F2 # 3 F3 + $ 14 × 1. BH THE BH3 2. H O NaOH '2 2' Click and drag to start drawing a structure. F4 Q W E R A S D % 905 LL F5 F6 F7 © 2025 McGraw Hill LLC. All Rights Reserved. Terms of Use | Privacy Center | Accessibility < & 6 7 27 8 T Y U G H I F8 F9 F10 F11 F12 9 0 J K L P + // command option Z X C V B N M H H rol option command

AG/F-2° V 3. Before proceeding with this problem you may want to glance at p. 466 of your textbook where various oxo-phosphorus derivatives and their oxidation states are summarized. Shown below are Latimer diagrams for phosphorus at pH values at 0 and 14: -0.93 +0.38 -0.50 -0.51 -0.06 H3PO4 →H4P206 →H3PO3 →→H3PO₂ → P → PH3 Acidic solution Basic solution -0.28 -0.50 3--1.12 -1.57 -2.05 -0.89 PO HPO H₂PO₂ →P → PH3 -1.73 a) Under acidic conditions, H3PO4 can be reduced into H3PO3 directly (-0.28V), or via the formation and reduction of H4P206 (-0.93/+0.38V). Calculate the values of AG's for both processes; comment. (3 points) 0.5 PH P 0.0 -0.5 -1.0- -1.5- -2.0 H.PO, -2.3+ -3 -2 -1 1 2 3 2 H,PO, b) Frost diagram for phosphorus under acidic conditions is shown. Identify possible disproportionation and comproportionation processes; write out chemical equations describing them. (2 points) H,PO 4 S Oxidation stale, N