To compute:
(a) The electrical conductivity of a cylindrical silicon specimen.
(b) The resistance over the entire specimen length.

Answer to Problem 1QP
(a) The electrical conductivity of a cylindrical silicon specimen
(b) The resistance over the entire specimen length is
Explanation of Solution
Given:
The diameter of cylindrical silicon specimen,
The two probes separated by length,
The current carried by silicon specimen in an axial direction,
Minimum voltage across two probes,
The entire length of the silicon specimen,
Explanation:
Write the equation for electrical conductivity
Write the expression of electrical resistivity
Write the expression for voltage.
Write the equation to calculate area
Conclusion:
Substitute
Substitute
Substitute
Thus, the electrical conductivity of a cylindrical silicon specimen
Substitute
Substitute
Thus, the resistance over the entire specimen length is
Want to see more full solutions like this?
Chapter 12 Solutions
FUND MAT SCI+ENG ACCESS+EPUB
- I need help with this problem and an explanation of the solution for the image described below. (Introduction to Signals and Systems: Sampling)arrow_forward(c) Consider the following set of processes: Process ID Arrival Time Priority Burst Time A 2 3 100 B 6 C 10 1 (highest) 2 40 80 D 16 4 (lowest) 20arrow_forwardShow workarrow_forward
- 13. The front of the platoon (truck) has a speed of 30 mph in question 12. According to the shockwave speed, the platoon is growing at a rate of:arrow_forwardProblem 1 (a) Suppose the Laplace transform of a causal signal x₁ (t) is given by S X₁(s) = 52 +2 Using the Laplace transform properties, find the Laplace transform of the following signal x2(t). x2(t) = e2t+1 x₁(t − 1) - tx₁(2t - 1) (b) Suppose an LTI system T whose impulse response is given by h(t) e 2t 1(t) t 1(t) +28(t) What is the transfer function of the system? (c) If the input x2 (t) is applied to the system T, what will be the output Y₂(s)? Note, you just need to provide Laplace transform of the output y₂(t). Simplification is not needed in any part of this question.arrow_forwardShow workarrow_forward
- A tank transmits 100 L/s of water to point C, where the pressure is maintained at 1.5 kg/cm². The first part, AB of the pipe, is 50 cm in diameter and 2.5 km long, and the second part BC is 25 cm in diameter and 1.5 km long. The friction coefficient is 0.005, and minor losses are ignored. Assuming the level at C is (0.0), find the water level (L) in the tank. L A B с hAB hBC bcarrow_forwardGiven a portion of a pipe network below. Determine the true discharge in each pipe using the Hardy-Cross method. Use the Darcy-Weisbach formula with f = 0.02 for all pipes. Pipe AB Length (m) Diameter (cm) 600 25 BC 400 25 CD 900 30 DA AC 1000 20 1500 20 Q₁₁ = 0.20 m³/s B Qc = 0.30 m³/s Loop I QA 0.10 m³/s A. C Loop II Q₁ = 0.20 m³/sarrow_forwardThe figures below shows the framing plan and section of a reinforced concrete floor system. Floor beams are shown as dotted lines. The weight of the ceiling and floor finishing is 6 psf, that of the mechanical and electrical systems is 7 psf, and the weight of the partitions is 180 psf. The floor live load is 105 psf. The 7 in. thick slab exterior bay (S-1) is reinforced with #5 rebars @ 10 in. o.c. as the main positive reinforcement at the mid span, and #4 @ 109 in. for the shrinkage and temperature reinforcement. The panel is simply supported on the exterior edge and monolithic with the beam at the interior edge. Check the adequacy of the slab. Use the ACI moment coefficients. fc’ = 6,000 psi and fy = 60,000 psi. The slab is in an interior location. Hint: • Estimate total dead load. Find factored maximum positive bending moment in the end span. • Find design positive moment capacity. • Compare and determine adequacy, including safety and economy.arrow_forward
- Question 6 Two reservoirs have a 6 m difference in water levels and are connected by a pipe 60 cm in diameter and 3000 m long. Then, the pipe branches into two pipes, each 30 cm in diameter and 1500 m long. The friction coefficient is 0.01. Neglecting minor losses, determine the flow rates in the pipe system. Q Q3 ha h₁ = 6 marrow_forwardDesign a simply supported one-way pavement slab for a factored applied moment, Mu = 10 ft- kip. Use f c’ = 5,000 psi and f y = 60,000 psi. The slab is in permanent contact with soil. Hint: • Estimate a minimum slab thickness for deflection control. • Solve for the slab steel based on cover for soil contact.arrow_forward20. In a deterministic queue, suppose vehicle arrive at a rate of 100 vph for the first hour and 60 vph for the second hour. The server can discharge 80 vehicles per hour. What is the standing queue at the end of two hours:arrow_forward
- MATLAB: An Introduction with ApplicationsEngineeringISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons IncEssentials Of Materials Science And EngineeringEngineeringISBN:9781337385497Author:WRIGHT, Wendelin J.Publisher:Cengage,Industrial Motor ControlEngineeringISBN:9781133691808Author:Stephen HermanPublisher:Cengage Learning
- Basics Of Engineering EconomyEngineeringISBN:9780073376356Author:Leland Blank, Anthony TarquinPublisher:MCGRAW-HILL HIGHER EDUCATIONStructural Steel Design (6th Edition)EngineeringISBN:9780134589657Author:Jack C. McCormac, Stephen F. CsernakPublisher:PEARSONFundamentals of Materials Science and Engineering...EngineeringISBN:9781119175483Author:William D. Callister Jr., David G. RethwischPublisher:WILEY





