Classical Dynamics Of Particles And Systems
Classical Dynamics Of Particles And Systems
5th Edition
ISBN: 9788131518472
Author: Stephen T. Thornton, Jerry B. Marion
Publisher: Cengage Learning India
Question
Book Icon
Chapter 12, Problem 12.1P
To determine

The characteristic frequencies of the two coupled oscillators with all spring constants different, and to compare it with the natural frequencies of the two oscillators in the absence of coupling.

Expert Solution & Answer
Check Mark

Answer to Problem 12.1P

The characteristic frequencies of the two coupled oscillators with all spring constants different are ω+=(k1+k2+2k122M+12M(k1k2)2+4k122)1/2 and ω=(k1+k2+2k122M12M(k1k2)2+4k122)1/2. In the absence of coupling ω+>ω01 and ω<ω02 where ω01 and ω02 are the frequencies when mass m2 and m1 are held fixed respectively.

Explanation of Solution

The system of the two coupled oscillators with all spring constants different are shown in Figure 1.

Classical Dynamics Of Particles And Systems, Chapter 12, Problem 12.1P

In the figure, the spring constants of the springs are marked as k1, k2, and k12.

Write the equations of motions for the system.

  Mx¨1+(k1+k12)x1k12x2=0Mx¨2+(k2+k12)x2k12x1=0}        (I)

Let us attempt the solutions of the form;

  x1(t)=B1eiωtx2(t)=B2eiωt}        (II)

Here, B1 and B2 are constants.

Use the solutions in (II) in (I).

  (k1+k12Mω2)B1k12B2=0k12B1+(k2+k12Mω2)B2=0}        (III)

The condition for obtaining a non-trivial solution is that, the determinant of the coefficients of B1 and B2 must be zero. Thus, it yields;

  [k1+(k12Mω2)][k2+(k12Mω2)]=k122        (IV)

Solve equation (IV) to get an expression for ω2.

  ω2=k1+k2+2k122M±12M(k1k2)2+4k122        (V)

Thus, the characteristic frequencies will be;

  ω+=(k1+k2+2k122M+12M(k1k2)2+4k122)1/2

  ω=(k1+k2+2k122M12M(k1k2)2+4k122)1/2

Consider the case; k1=k2=k, then equation (V) reduces to;

  ω2=(k+k12±k12)M

If the mass m2 is not moving, then the frequency of oscillation of m1 will be;

  ω012=1M(k1+k12)        (VI)

If the mass m1 is not moving, then the frequency of oscillation of m2 will be;

  ω022=1M(k2+k12)        (VII)

Comparing equation (VI) and (VII) with the two frequencies given by equation (V), it can be observed that;

  ω+2=12M[k1+k2+2k12+(k1k2)2+4k122]ω+2>12M[k1+k2+2k12+(k1k2)]ω+2>12M[2k1+2k12]ω+2>1M[k1+k12]ω+2>ω012        (VIII)

Similarly;

  ω2=12M[k1+k2+2k12(k1k2)2+4k122]ω+2<12M[k1+k2+2k12(k1k2)]ω+2<12M[2k2+2k12]ω+2<1M[k2+k12]ω+2<ω022        (IX)

From equation (IX) and (X) it is clear that;

  ω+>ω01ω<ω02

If k1>k2, then the ordering of the frequencies will be as;

  ω+>ω01>ω02>ω

Conclusion:

Therefore, the characteristic frequencies of the two coupled oscillators with all spring constants different are ω+=(k1+k2+2k122M+12M(k1k2)2+4k122)1/2 and ω=(k1+k2+2k122M12M(k1k2)2+4k122)1/2. In the absence of coupling ω+>ω01 and ω<ω02 where ω01 and ω02 are the frequencies when mass m2 and m1 are held fixed respectively.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
How can you tell which vowel is being produced here ( “ee,” “ah,” or “oo”)? Also, how would you be able to tell for the other vowels?
You want to fabricate a soft microfluidic chip like the one below. How would you go about fabricating this chip knowing that you are targeting a channel with a square cross-sectional profile of 200 μm by 200 μm. What materials and steps would you use and why? Disregard the process to form the inlet and outlet. Square Cross Section
1. What are the key steps involved in the fabrication of a semiconductor device. 2. You are hired by a chip manufacturing company, and you are asked to prepare a silicon wafer with the pattern below. Describe the process you would use. High Aspect Ratio Trenches Undoped Si Wafer P-doped Si 3. You would like to deposit material within a high aspect ratio trench. What approach would you use and why? 4. A person is setting up a small clean room space to carry out an outreach activity to educate high school students about patterning using photolithography. They obtained a positive photoresist, a used spin coater, a high energy light lamp for exposure and ordered a plastic transparency mask with a pattern on it to reduce cost. Upon trying this set up multiple times they find that the full resist gets developed, and they are unable to transfer the pattern onto the resist. Help them troubleshoot and find out why pattern of transfer has not been successful. 5. You are given a composite…
Knowledge Booster
Background pattern image
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Classical Dynamics of Particles and Systems
Physics
ISBN:9780534408961
Author:Stephen T. Thornton, Jerry B. Marion
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Text book image
Modern Physics
Physics
ISBN:9781111794378
Author:Raymond A. Serway, Clement J. Moses, Curt A. Moyer
Publisher:Cengage Learning
Text book image
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Text book image
University Physics Volume 2
Physics
ISBN:9781938168161
Author:OpenStax
Publisher:OpenStax
Text book image
University Physics Volume 3
Physics
ISBN:9781938168185
Author:William Moebs, Jeff Sanny
Publisher:OpenStax