
Concept explainers
For the conic helix of Prob. 11.95, determine the angle that the osculating plane forms with the y axis.
(a)

The angle
Answer to Problem 11.180P
The angle
Explanation of Solution
Given Information:
The three dimensional motion of a particle is defined by the position vector
Calculation:
Write three dimensional motion of particle position vector equation.
Write the expression for velocity using the relation:
Substitute
Here,
Write the expression for acceleration using the relation:
Substitute
Show the vector
Calculate the vector
Substitute
Calculate the
Calculate the
Calculate the angle
Substitute
Write the expression for angle
Substitute
Substitute
Show the representation of equation (4) as in Figure (2):
Calculate the angle
Therefore, the angle
Want to see more full solutions like this?
Chapter 11 Solutions
VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS
- Problem 22: Determine the force in members GF, FC, and CD of the bridge truss and state if the members are in tension or compression. F 15 ft B D -40 ft 40 ft -40 ft 40 ft- 5 k 10 k 15 k 30 ft Earrow_forwardProblem 20: Determine the force in members BC, HC, and HG. After the truss is sectioned use a single equation of equilibrium for the calculation of each force. State if the members are in tension or compression. 5 kN 4 kN 4 kN 3 kN 2 kN B D E F 3 m -5 m- -5 m- 5 m 5 m-arrow_forwardAn experimental setup is being built to study the flow in a large water main (i.e., a large pipe). The water main is expected to convey a discharge (Qp). The experimental tube will be built at a length scale of 1/20 of the actual water main. After building the experimental setup, the pressure drop per unit length in the model tube (APm/Lm) is measured. Problem (19): Given the value of Qp [m³/s], and assuming Reynolds number similitude between the water main and experimental tube, calculate the flow rate in the model tube (Qm) in [lit/s]. = 30.015 m^3/sarrow_forward
- Problem 11: The lamp has a weight of 15 lb and is supported by the six cords connected together as shown. Determine the tension in each cord and the angle 0 for equilibrium. Cord BC is horizontal. E 30° B 60° Aarrow_forwardProblem 10: If the bucket weighs 50 lb, determine the tension developed in each of the wires. B $30° 5 E D 130°arrow_forwardProblem 3: Four-Force Equilibrium Knowing the forces in members A and C, determine the force of B and D, assuming the system is in equilibrium. A structural joint is held in equilibrium by four forces acting along different members. • Member A applies a force of 4 kN at an angle of 60° above the positive x-axis. • Member C applies a force of 2 kN horizontally to the left along the x-axis. • Member B applies an unknown force along the horizontal direction. • Member D applies an unknown force at an angle of 45° above the negative x-axis. Determine the forces in members B and D, assuming the system is in static equilibrium. 4 kN 2 kN C 45° A D 60° FB Barrow_forward
- Problem 18: Determine the force in each member of the truss. State if the members are in tension or compression. 3 ft 3 ft 3 ft B D 4 ft 4 ft. 130 lb Earrow_forwardProblem 16: Determine the force in each of the member of the truss and state if the members are in tension or compression. Set P₁ = 10 kN, P2 = 8 kN. 2 m G F E A A 1 m B 2 m 1 m P1 Darrow_forwardProblem 7: Determine the force in each cord for equilibrium of the 60-kg bucket. D E 4 m 4 m B 3 m- 3 m- 3 m.arrow_forward
- Problem 15: Determine the reactions at the pin A and the tension in cord BC. Set F = 40 kN. Neglect the thickness of the beam. 26 kN F 13 12 -2 m 4 m B 4arrow_forwardProblem 21: Determine the force in members EF, CF, and BC and state if the members are in tension or compression. 1.5 m 4 kN E D 8 kN B 2 m 2 marrow_forwardProblem 8: If the cords suspend the two buckets in the equilibrium position, determine the weight of bucket B. Bucket A has a weight of 60 lb. E 65° C 20° 40° F B 20° Aarrow_forward
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE LPrinciples of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning

