Concept explainers
Blood pressure is usually measure by wrapping a closed air-filled jacket equipped with a pressure gage around the upper arm of a person at the level of the heart. Using a mercury manometer and a stethoscope, the systolic pressure (the maximum pressure when the heart is pumping) and the diastolic pressure (the minimum pressure when the heart is resting) are measured in mmHg. The systolic and diastolic pressures of a health person are about 120 mmHg and 80 mmHg, respectively, and are indicated as 120/80. Express both of these gage pressures in kpa, psi, and meter water column.
The systolic and diastolic pressure of a healthy person is expressed in a kPa water column for high.
The systolic and diastolic pressure of a healthy person is expressed in a kPa water column for low.
The systolic and diastolic pressure of a healthy person is expressed in a psi water column for high.
The systolic and diastolic pressure of a healthy person is expressed in a psi water column for low.
The systolic and diastolic pressure of a healthy person is expressed in a meter water column for high.
The systolic and diastolic pressure of a healthy person is expressed in a meter water column for low.
Answer to Problem 69P
The systolic and diastolic pressure of a healthy person is expressed in a kPa water column for high is
The systolic and diastolic pressure of a healthy person is expressed in a kPa water column for low is
The systolic and diastolic pressure of a healthy person is expressed in a psi water column for high is
The systolic and diastolic pressure of a healthy person is expressed in a psi water column for low is
The systolic and diastolic pressure of a healthy person is expressed in a meter water column for high is
The systolic and diastolic pressure of a healthy person is expressed in a meter water column for low is
Explanation of Solution
Show the free body diagram of the systolic and diastolic pressure of a healthy person.
Write the expression of gauge pressure.
Here, the density is
Write the expression of gauge pressure for water.
Write the expression of gauge pressure for mercury.
Substitute Equation (III) into Equation (II)
Conclusion:
Write the unit conversion from mm of Hg to m of Hg.
For
For
Substitute
Substitute
Write the unit conversion from kPa to psi.
For
For
Substitute
Substitute
Thus, systolic and diastolic pressure of a healthy person is expressed in a kPa water column for high is
Want to see more full solutions like this?
Chapter 1 Solutions
Thermodynamics: An Engineering Approach ( 9th International Edition ) ISBN:9781260092684
Additional Engineering Textbook Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Mechanics of Materials (10th Edition)
Experiencing MIS
Fluid Mechanics: Fundamentals and Applications
Elementary Surveying: An Introduction To Geomatics (15th Edition)
- The primary material used in the production of glass products is silica sand. True or Falsearrow_forwardWhich one of the following is the most common polymer type in fiber-reinforced polymer composites? thermosets thermoplastics elastomers none of the abovearrow_forwardA pattern for a product is larger than the actual finished part. True or Falsearrow_forward
- Two forces are applied as shown to a hook support. The magnitude of P is 38 N. 50 N 25° DG a 터 Using trigonometry, determine the required angle a such that the resultant R of the two forces applied to the support will be horizontal. The value of a isarrow_forwardNo chatgpt pls will upvotearrow_forward101 the three shafts if the diameter ratio is 2 (D/d = 2)? Ans. na, tension = 1.21, na, bending = 1.19, na, torsion = 1.17. 6.32 A material with a yield strength of S₁ = 350 MPa is subjected to the stress state shown in Sketch c. What is the factor of safety based on the maximum shear stress and distortion energy theories? Ans. For MSST, n, = 11.67. 50 MPa 85 MPa 20 MPa 70 MPa Sketch c, for Problems 6.32 and 6.33arrow_forward
- Can you draw the left view of the first orthographic projectionarrow_forwardImportant: I've posted this question twice and received incorrect answers. I've clearly stated that I don't require AI-generated working out. I need a genuine, expert-written solution with proper working. If you can't provide that, refer this question to someone who can please!. Note: Please provide a clear, step-by-step handwritten solution (no AI involvement). I require an expert-level answer and will assess it based on quality and accuracy with that I'll give it a thumbs up or down!. Hence, refer to the provided image for clarity. Double-check everything for correctness before submitting. Thank you!arrow_forwardNote: Please provide a clear, step-by-step simplified handwritten working out (no explanations!), ensuring it is done without any AI involvement. I require an expert-level answer, and I will assess and rate based on the quality and accuracy of your work and refer to the provided image for more clarity. Make sure to double-check everything for correctness before submitting appreciate your time and effort!. Question:arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY