DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 11, Problem 9RQ
To determine
The reason for visual inspection be considered as the initial and primary means of inspection.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
7.4 Impeller viscometer
The rheology of a Penicillium chrysogenum broth is examined using an impeller viscometer. The density of
the cell suspension is approximately 1000 kg m³. Samples of broth are stirred under laminar conditions
using a Rushton turbine of diameter 4 cm in a glass beaker of diameter 15 cm. The average shear rate
generated by the impeller is greater than the stirrer speed by a factor of about 10.2. When the stirrer shaft
is attached to a device for measuring torque and rotational speed, the following results are recorded.
Stirrer speed (s¹) Torque (Nm)
0.185
3.57 × 10-6
0.163
3.45 × 10-6
0.126
3.31 x 10-6
0.111
3.20×10-6
Can the rheology be described using a power-law model? If so, evaluate K and n.
(read image)
(read image) Answer Provided
Chapter 11 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 11 - What is the purpose of nondestructive examination...Ch. 11 - Why must destructive testing be performed on a...Ch. 11 - Prob. 3RQCh. 11 - What quality�related features can a hardness...Ch. 11 - Prob. 5RQCh. 11 - What are some possible objectives of...Ch. 11 - What are some factors that should be considered...Ch. 11 - How might the costs of nondestructive testing...Ch. 11 - Prob. 9RQCh. 11 - Prob. 10RQ
Ch. 11 - Prob. 11RQCh. 11 - Describe the sequence of activity in a liquid...Ch. 11 - What types of defects can be detected in a liquid...Ch. 11 - What is the basic principle of magnetic particle...Ch. 11 - Magnetic particle inspection is limited to the...Ch. 11 - Prob. 16RQCh. 11 - What is the major limitation of sonic testing,...Ch. 11 - Prob. 18RQCh. 11 - Prob. 19RQCh. 11 - What are three types of ultrasonic inspection...Ch. 11 - Prob. 21RQCh. 11 - What types of radiation can be used in...Ch. 11 - Prob. 23RQCh. 11 - What are penetrameters, and how are they used in...Ch. 11 - Although radiographs offer a graphic image that...Ch. 11 - Prob. 26RQCh. 11 - Prob. 27RQCh. 11 - What types of detection capabilities are offered...Ch. 11 - Prob. 29RQCh. 11 - Prob. 30RQCh. 11 - Prob. 31RQCh. 11 - How can temperature be used to reveal defects?Ch. 11 - Prob. 33RQCh. 11 - What are some of the ways to evaluate strains...Ch. 11 - What kinds of product features can be evaluated by...Ch. 11 - What type of information can be obtained through...Ch. 11 - What are some of the techniques that can be used...Ch. 11 - Why is it necessary to determine the distinction...Ch. 11 - A manufacturing company routinely specifies...Ch. 11 - For each of the inspection methods listed, cite...Ch. 11 - Prob. 3PCh. 11 - Prob. 4PCh. 11 - Prob. 5PCh. 11 - Prob. 6PCh. 11 - The pulse�echo ultrasonic technique can be used...Ch. 11 - If V for a particular metal is 5000 m/sec and a...Ch. 11 - With nondestructive inspection methods using wave...Ch. 11 - Your overall container is restricted to the size...Ch. 11 - If additional funds could be provided to upgrade...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- This is part B Part A's question and answer was find moment of inertia (Ix = 3.90×10^5) and radius of gyration (kx = 21.861) Determine the centroid ( x & y ) of the I-section, Calculate the moment of inertia of the section about itscentroidal x & y axes. How or why is this result different fromthe result of a previous problem?arrow_forwardDetermine by direct integration the moment of inertia of theshaded area of figure with respect to the y axis shownarrow_forwardConsider the feedback controlled blending system shown below, which is designed to keep theoutlet concentration constant despite potential variations in the stream 1 composition. The density of all streamsis 920 kg/m3. At the nominal steady state, the flow rates of streams 1 and 2 are 950 and 425 kg/min,respectively, the liquid level in the tank is 1.3 m, the incoming mass fractions are x1 = 0.27, x2 = 0.54. Noticethe overflow line, indicating that the liquid level remains constant (i.e. any change in total inlet flow ratetranslates immediately to the same change in the outlet flow rate). You may assume the stream 1 flowrate andthe stream 2 composition are both constant. Use minutes as the time unit throughout this problem. Identify any controlled variable(s) (CVs), manipulated variable(s) (MVs),and disturbance variable(s) (DVs) in this problem. For each, explain how you know that’show it is classified.CVs: ___________, MVs: _____________, DVs: ______________ b) Draw a block diagram…arrow_forward
- A heat transfer experiment is conducted on two identical spheres which are initially at the same temperature. The spheres are cooled by placing them in a channel. The fluid velocity in the channel is non-uniform, having a profile as shown. Which sphere cools off more rapidly? Explain. V 1arrow_forwardMy ID# 016948724 last 2 ID# 24 Last 3 ID# 724 Please help to find the correct answer for this problem using my ID# first write le line of action and then help me to find the forces {fx= , fy= mz= and for the last find the moment of inertial about the show x and y axes please show how to solve step by steparrow_forwardMy ID# 016948724 last 2 ID# 24 Last 3 ID# 724 Please help to find the correct answer for this problem using my ID# first write le line of action and then help me to find the forces and the tension {fx= , fy= mz=arrow_forward
- My ID# 016948724 last 2 ID# 24 Last 3 ID# 724 Please help to find the correct answer for this problem using my ID# first write le line of action and then help me to find the forces {fx= , fy= mz=arrow_forwardmy ID is 016948724 Last 2 ID# 24 Last 3 ID# 724 please help me to solve this problem step by step show me how to solve first wirte the line actions and then find the forces {fx=, fy=, mz= and for the last step find the support reactions and find forcesarrow_forwardUppgift 1 (9p) 3 m 3 m 3 m 3 m H G F 3 m ↑ Dy D B AAY 30° 8 kN Ay Fackverket i figuren ovan är belastat med en punktlast. Bestäm normalkraften i stängerna BC, BG och FG.arrow_forward
- The cardiovascular countercurrent heat exchnager mechanism is to warm venous blood from 28 degrees C to 35 degrees C at a mass flow rate of 2 g/s. The artery inflow temp is 37 degrees C at a mass flow rate of 5 g/s. The average diameter of the vein is 5 cm and the overall heat transfer coefficient is 125 W/m^2*K. Determine the overall blood vessel length needed too warm the venous blood to 35 degrees C if the specific heat of both arterial and venous blood is constant and equal to 3475 J/kg*K.arrow_forwardThe forces Qy=12 kNQy=12kN and Qz=16 kNQz=16kN act on the profile at the shear center C. Calculate: a) Shear flow at point B (2 points)b) Shear stress at point D (3 points)arrow_forwardConsider the feedback controlled blending system shown below, which is designed to keep theoutlet concentration constant despite potential variations in the stream 1 composition. The density of all streamsis 920 kg/m3. At the nominal steady state, the flow rates of streams 1 and 2 are 950 and 425 kg/min,respectively, the liquid level in the tank is 1.3 m, the incoming mass fractions are x1 = 0.27, x2 = 0.54. Noticethe overflow line, indicating that the liquid level remains constant (i.e. any change in total inlet flow ratetranslates immediately to the same change in the outlet flow rate). You may assume the stream 1 flowrate andthe stream 2 composition are both constant. Use minutes as the time unit throughout this problem. d) Derive the first order process and disturbance transfer functions;Gp= Kp/(tou*s+1) and Gd=Kd/(tou*s+1) and calculate and list the values and units of the parameters. e) Using the given information, write the general forms of Gm, GIP, and Gv below(in terms of…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License