Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 11, Problem 4SQ
Refer to the circuit in Figure 11–10. What is the purpose of control relay CR in this circuit?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What are typical uses for control relays
What is the significance of relay protection in power systems?
a. Draw the relationship between excitation current and short circuit, and Please explain.
b. At what volts is the alternator end voltage short-circuited? At nominal voltage What will happen if a short circuit is made?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each cycle is 0.6x10-3 seconds. Find the period of conduction in each cycle and frequency of operation?arrow_forwardHow many parallel paths are there in the following armature windings: (a) six pole duplex-wave? (b) six-pole triplex-wave? (c) eight-pole simplex-wave? (d) eight-pole duplex-wave? (e) eight-pole triplex-wave? (f) eight-pole quad ruplex-wave?arrow_forwardIn the context of power system protection, what are the various types of relays and their functions in detecting faults and ensuring system safety?arrow_forward
- What is the role of relays in power system protection, and how do they work to prevent faults?arrow_forwardAn X1 volt,(122V) relay has an inrush rating of 700VA and a hold-in rating of 150VA. Note X1=122V Determine, 1) the hold-in current and, 2) the inrush current.arrow_forwardChoose the right answer. 1. The basic elements in any power system are 2. The reactors have the following problems 3. If a fault occurred between phases (A, B, and C) simultaneously the fault is called if the fault occurred on phase (A) only or phases (A, B), it may take the following types and ...... where or 4. The symmetrical component method is 5. Conditions for succesful operation of a power system are 6. The reason we use the numerical methods in load flow analysis is 7. The main diagonal of Y-bus numbers by a factor / not any) 8. The properties of the fault currents and (changes the signs / keeps the signs / multiplies the .... .... ....... rearrow_forward
- B: Relay is consist two circuits, what they are? And determine whether the next relay is normally open or normally closed. 3arrow_forwardWhich of the statement is true? A Normally closed (NC) relay contact is open when the relay coil is de – energized. It opens when the coil energizes, but returns to closed position when the coil de – energizes. O b. When a relay contact is normally open (NO), there is an open contact when the relay is energized. O c. A NO relay contact is open when the relay coil is de – energized. It closes when the coil energizes but returns to open position when the coil de – energizes. d. When a relay contact is Normally Closed (NC), there is a closed contact when the relay is energized.arrow_forwardList two Loop (PLL) in important uses. of phase locked analog Communication System.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage LearningPower System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Power System Analysis and Design (MindTap Course ...
Electrical Engineering
ISBN:9781305632134
Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma
Publisher:Cengage Learning
FMPR-103 pt1 l Power Systems Protection v1; Author: L&D for Protection and Control;https://www.youtube.com/watch?v=ELWncjsh5uE;License: Standard Youtube License