Explanation Given: The width of the cone is h . Half of the height of the cone is r . The constant density of cone is ρ . Show the intersection of the cone at the arbitrary point ( x , y ) as in Figure (1). Calculation: From Figure 1, Calculate the differential mass of the cone. d m = ρ d V (I) Here, the density of the material is ρ , and the volume of the disc is V . Substitute π y 2 d x for d V in Equation (I). d m = ρ ( π y 2 d x ) Here, the centroid of the differential element along the y - axis is y 2 . Compute the moment of inertia of the differential element parallel to the y -axis and about the x -axis. d I x = 1 2 d m y 2 (II) Substitute ρ ( π y 2 d x ) for d m in Equation (II). d I x = 1 2 ( ρ π y 2 d x ) y 2 = 1 2 ρ π y 4 d x (III) Substitute r h x for y in Equation (III). d I x = 1 2 ρ π [ r h x ] 4 d x = 1 2 ρ π r 4 h 4 x 4 d x Conclusion: Express the moment of inertia of the cone about the x -axis. I x = ∫ 0 h d I x (IV) Substitute 1 2 ρ π r 4 h 4 x 4 d x for d I x in Equation (IV)

15th Edition

ISBN: 9780137519132

Author: HIBBELER

Publisher: PEARSON

See similar textbooks

Concept explainers

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provi…

Videos

Question

Chapter 10.8, Problem 93P

To determine

The moment of inertia about the x -axis, in terms of the total mass m of the cone.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 10.8, Problem 92P

Chapter 10.8, Problem 94P

Students have asked these similar questions

Q. After a puncture a driver is attempting to remove a wheel nut by applying a force of P KN to one end of a wheel brace as shown in Fig. 1. In cross-section the brace is a hollow steel tube (see section aa) of internal diameter r mm and external diameter q mm. wheel nut n Position S P m r q Section aa Fig, 1 (a) Calculate (i) the twisting moment, (ii) the bending moment, and (iii) the shear force in the brace at position S due to the applied load P. (b) Calculate (i) the shear stress due to twisting, and (ii) the bending stress at position S. Note that the shear force will not produce any shear stress at S. (c) Calculate the maximum shearing stress in the brace at position S using the Maximum Shear Stress Criterion. 2 Mechanics of Materials 2 Tutorials Portfolio: Exercise 5 (d) If the maximum permissible shear stress in the steel is 200 MPa, determine the maximum torque that can be applied by the brace without the risk of failure at S.

Calculate the first 5 Fourier series coefficients (A0-4 and B1-5 ) for the estimated R wave.

Refrigerant-134a is expanded isentropically from 600 kPa and 70°C at the inlet of a steady-flow turbine to 100 kPa at the outlet. The outlet area is 1 m2, and the inlet area is 0.5 m2. Calculate the inlet and outlet velocities when the mass flow rate is 0.65 kg/s. Use the tables for R-134a. The inlet velocity is m/s. The outlet velocity is m/s.

Chapter 10 Solutions

ENGINEERING MECHANICS Â?? STATICS

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The moment of inertia about the x - axis, in terms of the total mass m of the cone.

Solution Summary: The author calculates the moment of inertia about the x - axis, in terms of the total mass m of a cone.

Concept explainers

Videos

The moment of inertia about the x -axis, in terms of the total mass m of the cone.

Want to see the full answer?

Chapter 10 Solutions