EBK ELECTRIC MOTOR CONTROL
10th Edition
ISBN: 9780100784598
Author: Herman
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 1, Problem 9SQ
To determine
Choose the correct option that does not represent the considering feature of the speed control of a motor.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Q2/ An air-filled rectangular waveguide is to be used to transmit signals at a carrier frequency of 6 GHz. Choose its dimensions so that the cutoff frequency of the dominant TE mode is 80% of the carrier frequency 6GHz and that of the TE01 is 70%.
A three-phase half-wave converter in Figure 2
is operated from a three-
phase Y-connected 208-V, 60-Hz supply and the load resistance is R = 10 2. If it
is required to obtain an average output voltage of 50% of the maximum possible
output voltage, calculate
(a) the delay angle a.
(b) the rms and average output currents.
(c) the average and rms thyristor currents.
(d) the rectification efficiency.
a
T₁
Van
T₂
vbn
Vcn
m
b
K
T3
*
Fig.2
Vo
fuw me
ic
R
L
B. Find an expression for output dc voltage in single phase (fully controlled thyristor rectifier taking
the effect of source inductance into consideration.
wwwwwwww
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- -Simplify the following equation? ABC A+B+Carrow_forwardA reflex klystron operates at the peak of the n-2 mode. If (V1/Vo)=0.363, find the efficiency. Assume ẞ=1. X' 1 1.2 1.52 2 2.408 J₁(X') 0.44 0.5 0.55 0.58 0.582arrow_forwarda. Find Thevenin equivalent resistance at ab terminals b. Equivalent Norton's current c. The current flow in 3kohm resistor is Do not use chatgpt need handwritten solutionarrow_forward
- Solve by hand do not use chatgpt or AI tool. Need step by step handwritten solution otherwise downvotearrow_forwardI need a solution supported by book sources, not by artificial intelligence. Choose the correct answer: 1. In AM, 50% modulation indicates that 33.3%.11.1%). of the total transmitted power is in the sidebands (0%,50% 2. To obtain coherent detection in AM receiver, an extra signal is added to the modulated signal, this signal called (PLL, IF carrier, pilot carrier, subcarrier). 3. The output spectrum of a modulator includes upper-side, lower-side frequencies, and the carrier frequency. (balanced, standard amplitude, SSB, none of the above) 4. When a signal is multiplied by the unit step function, (the positive time range is suppressed, the negative frequency range is suppressed, the negative time range is suppressed, the positive frequency range is suppressed). 5. DSB-LC requires coherent detection at the receiver, if the type of modulation is modulation, over modulation, critical modulation, none of them). 6. A continuous FT indicates a 7. In VSB transmission signal. (continuous,…arrow_forwardI need handwritten solution Do not use AI or chatgpt otherwise massive downvotearrow_forward
- I need integration of equations Sn(w) = 1/w2 = Sn(w) 10-6 watt/Hz Sn(w) 10-12 es =arrow_forwardI need Integration of equations S₁ (w) = In (|w] + 1)arrow_forwardFor the area shown in the figure, write the limits of integration using both the vertical and horizontal cross-sections, then evaluate the integrals. . Find the Fourier expression of the following periodic function 3 -3-2xarrow_forward
- I need a solution from an expert without artificial intelligence. Choose the correct answer: 1. In AMI code, the shapes of "1" and "O" are, bit dependent, not related to each other). 2. In FDM the guard band is used to decrease, maintain, not related to). 3. Higher number of levels in PCM produces, (the same, opposite to each other, next the overlap between FDM signals. (increase, (higher quantization error, less number of bits per sample, lower quantization error, the same number of bits per sample). Fe Av 4. If the maximum shift in frequency is 70 kHz and the minimum deviation in frequency of the actual signal is 109.93 MHz, what is the carrier frequency? (110 MHz, 110 kHz, 107 kHz, 102 MHz) 5. TDM of signals requires them to have the same amplitude, sampling frequency, energy). 6. In standard AM, the last step in the transmitter is subtracting, multiplying, dividing). . In digital carrier systems, PSK). (maximum frequency, maximum the carrier signal. (adding, has higher bandwidth.…arrow_forwardNeed Handwritten step by step solution. Do not use chatgpt or AIarrow_forwardA linear electrical load draws 11 A at a 0.72 lagging power factor./1 153. When a capacitor is connected, the line current dropped to 122 A and the power factor improved to 0.98 lagging. Supply frequency is 50 Hz. a. Let the current drawn from the source before and after introduction of the capacitor be 11 and 12 respectively. Take the source voltage as the reference and express 11 and 12 as vector quantities in polar form. b. Obtain the capacitor current, IC = 12 - 11, graphically as well as using complex number manipulation. Compare the results. c. Express the waveforms of the source current before (11(t)) and after (12(t)) introduction of the capacitor in the form Im sin(2лft + 0). Hand sketch them on the same graph. Clearly label your plots. d. Analytically solve i2(t) – i1(t) using the theories of trigonometry to obtain the capacitor current in the form, ¡C(t) = ICm sin(2πft + OC). Compare the result with the result in Part b.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning