(a)
Determine the energy associated while dropping the coal from the given height.
(a)
Answer to Problem 1P
The energy associated while dropping the coal is
Explanation of Solution
Given information:
Mass of the coal is
Vertical height is
Calculation:
Refer Appendix II, “Physical constants” for gravitational acceleration value in the textbook.
The value of gravitational acceleration is
Find the potential energy associated due to gravitation using the relation:
Therefore, the energy associated while dropping the coal is
(b)
Determine the energy associated while burning the coal.
(b)
Answer to Problem 1P
The energy associated while burning the coal is
Explanation of Solution
Given information:
Mass of the coal is
Calculation:
Let consider the coal contains 100% of carbon.
Refer Equation (1.13) in the textbook.
Combustion of 1 kg of carbon releases energy of
Convert 32.8 MJ into J:
Therefore, the energy associated while burning the coal is
(c)
Determine the energy associated while converting the mass of the coal into energy.
(c)
Answer to Problem 1P
The energy associated while converting the mass of the coal into energy is
Explanation of Solution
Given information:
Mass of the coal is
Calculation:
Refer Appendix II, “Physical constants” for speed of light value in the textbook.
The value of speed of light is
Find the energy associated using the relation:
Therefore, the energy associated while converting the mass of the coal into energy is
Compare the energy scale level for the three cases as follows:
The mass of energy while converting the mass
The energy due to burning
Want to see more full solutions like this?
Chapter 1 Solutions
MindTap Engineering for Dunlap's Sustainable Energy, SI Edition, 2nd Edition [Instant Access], 1 term (6 months)
- س (١) الشكل المرفق لقطعة أرض مستطيلة بعدها بالاتجاه الأفقي ١٢ متر ماهو مقياس الرسم لهذة الخارطة وماهو البعد بالاتجاه العمودي على الأرض . س (۲) ماهي انواع المساحة من حيث الدقة . س ۳) طريق يحتوي على ثلاث محطات المسافات بينهم متساوية المحطة الأولى A = 233457.8 متر المحطة الثانية 8 = 23.6+278 متر ماهي المحطة الاخيرة ) 12 marrow_forwardPlease solve with drawingarrow_forward止 Q.1 Using the lightest W section shape to design the compression member AB shown in Fig. below, the concentrated service dead load and live load is PD-40kips and PL 150kips respectively. The beams and columns are oriented about the major axis and the columns are braced at each story level for out-of-plan buckling. Assume that the same section is used for columns. Use Fy-50 ksi. 32456 Aarrow_forward
- 02. Design a W shape beam is used to support the loads for plastered floor, shown in Figure. Lateral bracing is supplied only at the ends. Depend LRFD and Steel Fy=50ksi. Note: The solution includes compute C, Check deflection at center of beam as well as shear capacity) B P10.5 P=140 W C Hing Hing 159 A 15.ftarrow_forward02. Design a W shape beam is used to support the loads for plastered floor, shown in Figure. Lateral bracing is supplied only at the ends. Depend LRFD and Steel Fy=50ksi. Note: The solution includes compute C, Check deflection at center of beam as well as shear capacity) B P10.5 P=140 W C Hing Hing 159 A 15.ftarrow_forwardName: Q.1 select the lightest W12 shape for column AB that support a service dead and live loads Po-150k and P-200k as shown in Figure. The beams and columns are oriented about the major axis and the columns are braced at top and mid-height using pinned end connections for out of plane buckling. ASTM A992 steel is used. Select the suitable answer below: I U B W18.76 8.00 All dimensions in feet 30.00 8091 B Parrow_forward
- Consider the structure shown in (Figure 1). Suppose that F = 2500 N. Figure 0.2 m 1500 N 0.2 m 30% 0.2 m B -0.2 m-0.2 m- F Part A Determine the resultant couple moment. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. ΜΑ ? 1 of 1 MR = 2.85 kN⚫m √30° 1500 N AUG 16 Submit Previous Answers Request Answer Incorrect; Try Again; 28 attempts remaining Provide Feedback Next > A W 20 Aaarrow_forwardExample The 30-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment of P about point B and about point A. Ans: Mb= 48 N.m Ma= 81.941 N.m P = 30 N 1.6 m 45° B 1.6 marrow_forwardQ2. Write the flexibility matrix corresponding to coordinates 1 and 2 for the structures shown. 13 ans: l 4 11 3 [16 51 6EI 126EI 5 2 (a) A -1- 2 (b) A B Constant EI 2arrow_forward
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning