Answered: ZL = 40 +j 30 Q. Find the following…

ZL = 40 +j 30 Q. Find the following numerically (without Smith chart): (1) Load admittance Y %3D 0.25 A (2) Zin (3) L 100 O 30 ti402

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.72P

See similar textbooks

Related questions

Q: approximate voltage amplitude and frequency of the waveform below

Q: 2. When a large shunt capacitor is suddenly connected in parallel with the load bus in the…

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: 610 510 12V +6V U Ka 510 R3 E 510 IN4007

A: In the circuit the current I1 is flowing through R1 and R3 and current I2 is flowing through R2 and…

Q: Choose the correct mode of operation for each MOS band diagram below. Vacuum level Vacuum level En…

A: We need to choose the correct mode of operation for each Mos band diagram.

Q: can not read the the simplifying the positive feed back loop part

Q: A single pulse 1nsec long is sent through a 50 ohms transmission line with a load resistance of 75…

A: To calculate the time it takes for the return current to reach the return conductor we first need to…

Q: Determine the region where the poles of a second-order system without zeros must be so that the…

A: Here we need to analyze the system's pole placement in the complex plane. A second-order system is…

Q: Convert the following logic gate circuit into a Boolean expression, writing Boolean sub-expressions…

A: Given data:Required information:

Q: 23. The capacitor does not allow sudden change in __________ A. voltage…

A: we need to select correct option for the statement:The capacitor does not allow sudden change in…

Question

microwave

Q4: Lossless transmission line of 0.25 having Z.
ZL = 40 +j 30 . Find the following numerically (without Smith chart):
(1) Load admittance Y
= 100 2 terminated by load impedance of
(2) Zin
0.25 A
(3) IL
Zo = 1002
Z̟= 30 + j40^
%3D
(4) SWR
Zin

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A lossless transmission line has a capacitance per unit length of 90 uF/m (microFarad/meter) and an inductance per unit length of 1 nH/m. The load impedance ZI is purely resistive. Both the load impedance and the generator impedance are 50 ohms. Source voltage amplitude is unknown at this point. Find the characteristic impedance and the propagation velocity for this transmission line!
2. A transmission line with Zo = 1000 and 1 = 0.42 is terminated with a Z₁ = 30+ j500 load. The internal impedance of generator is Zg. a) Find reflection coefficient at the load and SWR on the line by using Smith Chart. b) To be maximum power transfer to load, find the Zg value and maximum power Pmax
The impedance of the 500 km long transmission line is Z = 0.1 + j * 0.4 ohm / km. At the end of the line, 988.1 A current is drawn under 400 kV interphase voltage. The angle of the current is -68. It is 6 degrees. With the short transmission line equations, the amplitude value of the phase neutral value of the busbar voltage to which the generator at the beginning of the line is connected is given correctly. A) 231.34 B) 52.35 C) 400 D) 380.28 E) 388.57
Please help with an explanation for this problem.
A lossless transmission line has a capacitance per unit length of 64pF/m and an inductance per unit length of 1μH/m. The load impedance ZL is purely resistive. Both the load impedance and the generator impedance are 50 Ohms. the characteristic impedance and the propagation velocity
answer it i will rate
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
A DC generator of voltage Vg and internal resistance Rg is connected to a lossy transmission line characterised by a resistance per unit length R and a conductance per unit length G. a.)Write the governing voltage and current transmission line eequations. b.)Find the general solutions for v(z) and I(z). c.)Specialise the solutions in part(b) to those for an infinte line. d.)Specialize the solutions in part(b) to those for a finite line of length l that is terminated in a load resistance Rl.
ENG3043 Tutorial I A DC voltage source (Vs=10 V) is connected to a load (Z= 100 2) via a lossless transmission line (TML) as shown below. The voltage source has an internal impedance Zg–50 £2 and the TML has a characteristic impedance Z- 75 2. i. Calculate the phase velocity of the TML if its effective permittivity c is 2.56; ii. Calculate the source and load refection coefficients; iii. At t-0, the switch is closed. Draw the voltage waveform V(z.1) on the TML at t=2.5T where T is the time taken traveling from one end of the TML to the other and z refers to any position on the TML iv. Draw the voltage waveform at z=3/4 from the source for the time period between 0 and 37; v. If the switch was open at =1.57, draw the voltage waveform at z=l/2 from the source for the time period between 0 and 37
A lossless 60 ohm line is terminated by a 60+j60 ohm load .If Zin =120- j60ohm. How far (in term of wavelength) is the load from generator.
Transmission Lines: How do I solve this problem?
In a mismatched transmission line with intrinsic impedance of Z, and with a load of impedance of Z, , Zz + Z, . An extra length of transmission line is used to match it with load having an intrinsic impedance of Z, = Z,z, . The length of the transmission line used is, a) 1 b)