ZBR 07 ZYB Luad Supply

Q: What is a multipath channel? why is a multipath channel frequency selective?

A: Multipath channel Multipath channel (MPC) authorizes to code single transmission group for…

Q: What is program block and module .What is difference between "==" and "==="

A: Program block is new construct in System Verilog. The blocking and non blocking statement should not…

Q: Explain the role of microchips in modern electronics. How have microchips revolutionized the field…

A: We need to Explain the role of microchips in modern electronics.  We also need to explain How have…

Q: The channel capacity is Select one: O a. all of the mentioned O b. information contained in a signal…

A: The channel limit, C, is characterized to be the greatest rate at which data can be sent through a…

Q: What happened to the led speed blinking when the delay was changed?

A: /* Blinking LEDs- Program to run that the LED is connected to pin 6 and the delay is one second…

Q: Q2: Consider the following control system K, (1+ 18) For K. = 2, tD = 1 and step change in load…

A:

Q: Write an 8051 asm program to perform the following. The switch is connected to P1.5 and the LED…

A: Given  Switch = 0  - LED glow . Switch = 1 LED blink

Q: can i series my led chip even though i don't put any fuse. Is it safe?

A: Most of circuit does not contain fuse for LED Chip Reason behind not putting fuse for LED Chip is…

Q: Chose the correct answer 7- When does over-modulation occur? a) Modulating signal voltage carrier…

A: This question is related to the modulation process.    When does over-modulation occur?…

Q: (i) (ii) (iii) (iv) Calculate the frequency of the PWM signal. Calculate the duty cycle of the PWM…

A:

Q: Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be…

A: Given that : 6 bit ADC range (0-59) to Find Resolution :

Q: Match the signal state with its description. READY=1 A. The MPU has put valid data on the bus B.…

A: Here in left side specific signal is given in which * indicates the active low signal means it can…

Q: Mention the segments that must be logical 1 on the BCD seven segment common cathode to produce…

A:

Q: To control the brightness of LED using the instruction “analogWrite(led, brightness);”, _________…

A:

Q: Explain the steps for chip mounting.

A: Chip mounters are required for the mass manufacture of consumer and other electronic products…

Q: What is common channel signaling? And how does it work?

A: Common channel signalling  It is signalling in which a group of voice and data channels share a…

Q: Question : with Eight LEDs with 74HC595. This code uses a shift register to use a single data pin to…

A: Given data: 8 LEDs 74HC595 shift register Value of current LED=5 We have to find the value of the…

Q: A uniform quantizer, with average quantization power of 67.5 mW, is used in a PCM system. 1) What is…

A:

Q: What will happen if a signal, whose voltage is above the maximum tolerable voltage of the ADC, is…

A: If we give a voltage which is above maximum voltage of ADC then ,then the ADC will show its maximum…

Q: Q2-A-For VCO-LO that represent FM-TX if frequency of the carrier signal at -5 volt. Calculate the…

A: It is given that:

Q: The button is on the 3rd bit of PORTC. When the button is pressed, turn on all leds on PORTD. ORG…

A: Microcontroller (PIC16F877A):…

Q: Is the conversion time of the ADC constant or variable? What parameter does control it?

A: The conversion time of an Analog-to-Digital Converter (ADC) can be constant or variable depending on…

Q: Нomework 1. Convert (110101.11)BCD to ()2 directly.

A: Since the concept of BCD (binary coded decimal) is that we have to represent each decimal digit(from…

Q: Q2: Consider the following control system K. (1+ tos) 2 For K. = 2, tp = 1 and step change in load…

A:

Q: 1. Perform the following number system conversions: a. (366)7 = ?10 b. (A24C.5)16 = ?10 c. (815.6)10…

A:

Q: How the trailing current in IGBT is different from the MOSFET?

A: Trailing current is a phenomenon that occurs in both IGBTs (Insulated Gate Bipolar Transistors) and…

Q: To implement 8-to-1 line multiplexer using two 4-to-1 line multiplexer(MUX): O a. The third selctor…

A: The 8to1 multiplex can be implemented by two 4to1 multiplexer as shown below

Q: Use the schematic for our board to select the input signals on the I/O Memory selection hardware…

A: From the given options                                                       IO¯/M   =1  : operation…

Q: [0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of…

A: We need to calculate number of level , and step size for quantization .

Q: I have four ESP-WROOM-32D boards, and four NRF24L01 modules. Each ESP-WROOM-32D board is connected…

A: You can use the RF24 library for NRF24L01 modules and the ArduinoJson library for handling JSON…

Q: When a small letter r' is used in relation to a transistor, what does this mean? Please select one:…

A: Choose the correct option in the given question.    The small letter r' is used in relation to a…

Q: 16. What is the two's complement of 1011100111?

A: As per Bartleby guidelines we are allowed to solve only one question, please ask for rest again. The…

Q: There exists one or more discrete ime signal. What is it control system ? (a) discrete time or (b)…

A:

Current Division Method

The generalized current divider formula is given by the following relation below,