Your team is building a robot that is powered by a 35AH battery. During testing, the robot will run for a maximum of 5 hours before running out of battery, interrupting testing. The team would like to have a better idea of when the robot is going to run out of battery and needs to be recharged. An electrical engineer on your team designs a board to help solve this, with an LTC2944 and a 0.3mohm sense resistor. You are tasked with writing the software to read the accumulated battery discharge, in mAh, at the highest resolution possible. What should register bits B[5:3] be set to, in hexadecimal (please omit 'Ox' from your answer)? Look up the datasheet to answer this question.

Your team is building a robot that is powered by a 35AH battery. During testing, the robot will run for a maximum of 5 hours before running out of battery, interrupting testing. The team would like to have a better idea of when the robot is going to run out of battery and needs to be recharged. An electrical engineer on your team designs a board to help solve this, with an LTC2944 and a 0.3mohm sense resistor. You are tasked with writing the software to read the accumulated battery discharge, in mAh, at the highest resolution possible. What should register bits B[5:3] be set to, in hexadecimal (please omit 'Ox' from your answer)? Look up the datasheet to answer this question.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Subject=Digital Logic Design Need Conclusion Nothing else. A building security system works such that it uses the following ways of intrusion detection. Security cameras Motion sensors Security Guard The system works such that when an intruder is detected by either security cameras or motion sensors or the guard, the system not only sounds an alarm but also sends an sms alert to the security supervisor of the building.
Please help me Write the inputs and output E.g. input - A = 0 - B = 0 Output x = 0 And also input the inputs and outcomes E.g. 2 inputs = 4 outcomes
Q2: Write a C# program that generates an array Y(3x3) randomly (between 55, 666) and print: The average of prime number in secondary diagonal. The summation of each row. The number of odd elements of each even column. Note: Don't use classes or functions to solvethe question
3. Draw the combinational circuit that directly implements the Boolean expression on logisim/circuit lab. If drawn, no extra credit. No excuses. 15 points + 10 points extra credit if drawn and labeled with circuit drawing tools. a. xyz + (y' + z) b. x + xy + y'z c. (x (y z )) + (xz)'
Show a simple interface from an output port to drive an LED. Assume that the output port can sink or source up to 20 milliamps and the forward voltage of the LED is 2 volts. Show your calculations
There are two lamps used to illuminate the well, the first lamp is installed at the top of the wellI, and the second lamp is installed at a distance from the first using the Arduino board. Make the two lamps light at the same time using only one switch
How much energy is transferred to each eardrum in one second? (Hint: It may help to asume that the speaker is on the stage located 1.0 m from the edge.) Express your answer using two significant figures.
Take a look at the attached screenshot. Then, explain in your own words what would happen to the circuit if the below were to be adjusted: a) Frequencyb) Amplitudec) DC Offsetd) Time per Division Then, 2. Explain in words what would happen to the LED in the circuit for each of these adjustments.
I could use some help with making a working code for a 12 hour clock system in verilog for my DE0lite or any other Fpga Board. I am being unable to get the results correct
What program or software can do a simulation for slotted ALOHA?
Please explain how to do this I’m confused
Write a small PIC program in mikroC for turning on and off an led with same push button (Include the circuit)