Your first customer asked for an air piston-cylinder to use it in air compressors for generating high pressure. Your role in your company is to analyze, describe the operation of the system and their properties, explain and demonstrate the application of the first law of thermodynamics to this system, as well as, illustrate the importance of expressions for work done in the system through the application of the first law. Air Figure 1:Schematic for the air piston-gylinder. The required piston-cylinder device is frictionless and initially contains 3 kg of air at 150 kPa in 0.2 m?. The air is now heated by using a fire. Also, a mechanical shaft is rotating. Then the piston starts

Your first customer asked for an air piston-cylinder to use it in air compressors for generating high pressure. Your role in your company is to analyze, describe the operation of the system and their properties, explain and demonstrate the application of the first law of thermodynamics to this system, as well as, illustrate the importance of expressions for work done in the system through the application of the first law. Air Figure 1:Schematic for the air piston-gylinder. The required piston-cylinder device is frictionless and initially contains 3 kg of air at 150 kPa in 0.2 m?. The air is now heated by using a fire. Also, a mechanical shaft is rotating. Then the piston starts

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Discuss the meaning of modelling and analysis in Mechanical Vibratory System
LB Clear Water Tank Hz₁ (VSD Hz, VSD Figure 6. Extension of water inlet pipe into reservoir tank 1. Draw a block diagram of the system by considering the schematic diagram in Figure 6. hand written asap Reservoir tank F2
3. At a load of 43,000 KW in a steam turbine generating set, 3600 RPM, the following data appear in the log sheet. Steam flow -190 Metric Tons/hour Steam pressure - 8.93 MPaa Steam temperature - 535C Feed-water temperature - 230 C Fuel Flow: Bunker Oil -3.4 Metric Tons/hr HHV=10,000 Kcal/hr Local coal -18 Metric Tons/hr HHV = 5350 Kcal/hr Determine the overall boiler efficiency. h at 8.93 MPa and 535°C -3475.7 KJ/kg hf at 230°C-990.12 KJ/kg
We give: AB: adiabatic trigger such as VB = 2 VA AC: isothermal compression PA =1bar=105 Pa , VA = 10^-2 m3 Gas temperature at point A: TA= 300 Kelvin Perfect gas constant: R = 8,31 J.mol-1.K-1 Molar thermal capacity at constant pressure:Cp = 29 J.mol-1.K-1 Calorific capacity ratio of this gas: Cp/Cv = 1,40 4 – Calculate the amount of QBC heat and WBC work received by the system for the transformation that changes the system from state B to state C.5 – a – Why is the UCA internal energy variation of the gas zero during the CA transformation? b – Apply the first principle to the ABCA cycle and deduce the WAB work received by the gas during theadiabatic relaxation AB.c – Interpret the WAB sign.
276mmx164mm compressor has a piston displacement of 0.039cum/s, what is the operating speed of the compressor if [13] one cyclinder [14] V8 [15] W16 Please answer this immediately. Thank you!
[Hydraulics] Derive a formula for the momentum force acting on a stream tube due to velocity variation.
NFPA means - a. O a. National Fluid Power Association b. National Fluid Power Activation OC. Net Fluid Pressure С. Activity d. Net Fluid Power Association
Anideal gas with a mass of 2 kg reversibly and polytropically expands up to 3 times its initial volume in a piston-cylinder assem bly. The temperature of the ideal gas drops from 300° Cto 60° C. (a) If the heat energy inputis 20 kJand the boundary work output is 100 kJ, the specificheats of the gas cv [kJ/ kgK] and find the cp [kJ/ kgK] values. (b) If the heat energy output is 20 kJand the boundary work output is 100 kJ, the specificheats of the gas cv [kJ/ kgK] (c) Find the value k, which is the ratio of specificheats. (d) If the heat energy input is 20 kJ, the boundary work output is 100 kJ and the entropy generation is 0.36 kJ/K, then the thermal energy Calculate the source tem perature as [° C].
1. What is a fluid? kg [6 marks] 2. A tank is filled with oil with density p = 830; If the volume of the tank is V = 1.01m³ determine the amount of mass in the tank in kilograms. Show your workings. m³ [6 marks] 3. A pipe of diameter 0.18 m has a flow rate of 0.025 m³/s, what is the average velocity in the pipe? Show your workings. [6 marks] 4. The flow rate in a pipe is 1446 litres per minute, what is this in SI units Show your workings. )? [5 marks] 5. The equation below is a simplified form of the continuity equation. dm dt CV Σmin -Σmout The derivative term with respect to time is which of the following: a. The rate of change of the mass within a given control volume b. Always zero by definition c. Zero for transient time dependant flow conditions d. Zero when the mass flow rate coming into the control volume is smaller than the mass flow rate exiting the control volume e. Zero when the mass flow rate entering the control volume is greater than the mass flow rate leaving the…
A wind turbine gives the following data: Blade length= 57.5 m. Wind speed = 13 m/s Air density = 1.225 Kg/m3 Power coefficient = 0.45 Assuming equal efficiencies for gearbox and generator, If the Power output from wind turbine, P is 1.9 MW, then find
I need the answer as soon as possible