Your colleague at the power plant station initiated a mutual discussion, where he suggested applying Carnot cycle since it is considered the optimal cycle that steam power plant may be operated on. You were in position to justify him why there many difficulties and impracticalities associated with the Carnot cycle in terms of steam power plant, deliver a brief report explain why the Rankine cycle is preferred over the Carnot cycle in steam production plants, mention all impracticalities associated with applying Carnot cycle including the limitation of boiler and condenser temperature and pressure with respect to the surrounding saturation conditions (vou may construct TS diagrams for both cycle to demonstrate your comparison).

Your colleague at the power plant station initiated a mutual discussion, where he suggested applying Carnot cycle since it is considered the optimal cycle that steam power plant may be operated on. You were in position to justify him why there many difficulties and impracticalities associated with the Carnot cycle in terms of steam power plant, deliver a brief report explain why the Rankine cycle is preferred over the Carnot cycle in steam production plants, mention all impracticalities associated with applying Carnot cycle including the limitation of boiler and condenser temperature and pressure with respect to the surrounding saturation conditions (vou may construct TS diagrams for both cycle to demonstrate your comparison).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A car is able to provide 300kW of tractive power, as it accelerates from 36 to 288km/hr, along a flat and level section of road. This is achieved in 2 seconds. a) Calculate the tractive force at 36km/hr.
Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 641lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the fulcrum how long was the seesaw on Joe's side?
Convert between energy units. 132x10^4 kJ to kcal
2. A small system requires 0.875 in.w. total pressure at a flow rate of 1420 cfm and outlet air speed velocity of 2000 fu/min. a) Select the suitable smallest size belt drive fan b) Sketch the system and fan characteristics showing the operating point c) Specify the fan speed (rpm) and the power (bhp) d) Calculate the motor power, kW e) Specify the required fan pulley diameter for 6" drive pulley diameter
Resolve and draw the diagram of all internal efforts.
Task 1 You are employed as a mechanical engineer within an unnamed research center, specializing in the development. of innovative air conditioning systems. Your division is tasked with providing computer-based modeling and design solutions using computational fluid dynamics through ANSYS software. Your primary responsibilities. involve the analysis of horizontal channel dynamics to meet specific criteria. Under the guidance of your immediate supervisor, you have been assigned unique responsibilities within an ongoing project. As a member of the research team, your role includes constructing an appropriate model and executing a sequence of simulation. iterations to explore and enhance channel performance. Figure 1 provides a visualization of the horizontal channel under consideration. Consider 2D, incompressible, steady flowin a horizontal channel at a Reynolds number of 150. The schematic below illustrates the channel flow, not drawn to scale. For simplicity, neglect gravity. The…
Q3/ including setting the machine, a worker manufactures 79 pieces of different tools in 7 hours and 15 minutes. If the standard time for the tool was Setting time = 40 min Production time per tool= 10 min Compute: 1-The standard time for manufacturing the 79 tools 2-Efficiency of operator
In a manufacturing process, a drill press automatically drills a hole into a sheet metal part on a conveyor. In the drilling operation the drill bit starts at rest direcdly above the part, descends quickly, drills a hole, and quickly returns to the start position. The maximum vertical speed of the drill bit is 4 in./s, and while drilling the hole, it must move no more than 2.6 in./s to avoid warping the metal. Let s(t) be the drill biť's height (in inches) above the part as a function of time t in seconds. Sketch possible graphs of the drill bit's velocity [s'(t)] and acceleration [s"(t)].
i need the answer quickly
Q2 Sustainability is the concept of a lasting forward-looking development of all economic, ecological and social aspects of human existence. These three pillars of sustainability are interdependent and require a balanced coordination.
Question 44: Raise examples of areas or locations severely affected by some of the problems listed below and comment - Acid depositions - Climate change and the greenhouse effect - Degradation of groundwater and surface water quality - Soil degradation - Habitat and biodiversity reduction - Ozone hole - Degradation of urban living conditions - Insertion of toxic substances into the food chain
P5/ Find the equation tor the plane through Plo,2,-1) and normel to n= 3i - 2-k