You were working as an electrician and a large steel manufacturing plant and you are in the process of doing preventive maintenance on a large DC generator you have Meg both a series and shot field warnings and found out each has over 10 and resistance to grow your own meter however indicator resistance of 1.5 resistance across terminals S1 and S2. The ohmmeter indicates a resistance of 2 to 5 resistance between terminals F1 and F2 are these readings normal for this type of machine

Q: Copper brushes in D.C. machine are used where low voltage and high currents are involved where high…

A: This is a problem of dc machines. The solution is given in the next step

Q: Problem 1 A core with a coil has 240 turns, to generate a flux ø of 0.008482 weber, how much should…

A: Here, we have given a core with a coil having 240 turns, the value of flux is given. And, we have to…

Q: How does the load power vary with the load resistance

A:

Q: f. If the upper sphere fell down on ground by accident, and its shape became irregular with having…

A: Any charged particle produces an electric field. This electric field is directed from the positive…

Q: Q10. To produce a voltage output to 9-Volt of the DC power supply circuit shown in Figure 3, what…

A: R1 = 100 Ω Expression for Vout - Vout= Vref.x 1+R2R1+ Iadj.x R2 Iadj. is negligible most of the…

Q: This is a question about coil winding. a)Look at the diagram in FIGURE1. Describe the path for one…

A: The given figure is shown below,

Q: would like to know how electromagnetism is related to wind-energy conversion systems?

A:

Q: D.C. generator will be in a position to build up without any residual magnetism compound series…

A: To start DC generarator residual magnetism is required, if it is not present then by method of…

Q: a student is testing out different ways of making a hydroelectric.  This machine uses moving water…

A: Hydro electricity- The generation of electricity from the water movement is called as…

Q: Determine in which part is the Power Control Circuit and Control Center.

A: A circuit diagram is given in the question. In the given schematic we need to determine which part…

Q: In AC voltage controls, do the two thyristors work at the same time? What happens if they work at…

A: In AC voltage controls, do the two thyristors work at the same time? What happens if they work at…

Q: In a transformer setup, if your input voltage is V1 = 20VAC, what ratio of turns would you use to…

A: In this question we will try to find the relation between the emf and the number of turns in the…

Q: A welding power source must not be used continuously in long time without care. The rated duty cycle…

A: A transformer-style welding power supply converts moderate voltage, moderate current electricity…

Q: Two generators having X 1= 0.2 P1-60, and ) 2 = 0.3P +40.

A:

Q: I need as many machines as possible, without explanation, just a number

A: Electrical machines are defined as an rotating device which either takes mechanical input to produce…

Q: briefly describe the phenomenon of magnetic hysteresis.

A: Firstly I will define magnetic hysteresis. Then I will explain the hysteresis curve. Then I will…

Q: 4- A 100kW, belt driven shunt generator running at 300rpm on 220V bus bars continue to run as a…

A: Generated emf = terminal voltage +voltage drop in armature resistance +brush voltage drop. Back emf…

Q: CLO2-A core is wrapped with a 400 nim coil that carries a current of 380 mA. If the reluctance of…

A: Given, A core is wrapped with coil. Number of turns in the coil, N=400. Current in the coil, I=380…

Q: Vertical axis wind turbine has blades like O a. Airplane propeller O b. Cylindrical bamboo structure…

A: Find explanation below

Q: Look carefully at the figure and answer the following questions. For your answers choose between on…

A: There will be the concept of Lenz's law. Because Faraday's first law i.e., tells us that if you will…

Q: Is the equilibrium point C stable? Please describe your answer Load torque TL1 A Motor torque T Load…

A:

Q: 2. a) i. ii. For the circuit presented in Figure 2, Vin = 50 V, turns ratio between primary and…

A: The circuit based on the information provided.Here's how to approach the questions:i. Duty Cycle and…

Q: 11. There is 900 mA of current through a wire with 40 turns. What is the reluctance of the circuit…

A:

Q: active elements/conductors

A:

Q: Iron losses in a DC machines are independent of variations in: * voltage and current speed and…

A: The iron loss is classified in two types, Hysteresis loss and Eddy current loss. Where, Eddy current…

Q: CLO2-A core is wrapped with a 400 nim coil that carries a current of 380 mA. If the reluctance of…

A: We need to find out the flux for given coil .

Q: Voltage (Voltage) Regulator Alternators without Excitation Machine (Constant Voltage Generators)…

A: Voltage Regulators: A voltage regulator is an electrical or electronic device that can hold…

Q: List four electrical injuries and the cause of each

A: Electrical injuries take place due to various causes.

Q: An alternating voltage is given by v1 = 95 sin( 200 Tit -0.3 ) volts. What is the phase angle…

A: Given: V1=95 sin200 πt-0.3Volts V2=95 sin200πt

Q: digital communication I need Line codes for bits stream [101000110]. 1-Unipolar Rz and Unipolar NRz…

A: The digital data encoding schemes are categorized into five types based on their synchronization…

Q: 47. Flux linkage is equal to: a. Product of number of turns and magnetic flux b. Number of turns…

A:

Q: h of the following load is Inductive in nature tor hontor

A: Water heater is a resistive load and uses heat produced by resistors to heat water.

Q: connected to commutator 1 :

A: The answer is provided in the below step.

Q: A dc machine has a constant of k=10, þ=0.3web, V3=200V, and full load speed of w=20rad/s rotates…

A: a dc machine has a constant of k=10, Φ=0.3 Web, VB = 200V and full load speed of ω=20 rad/sec…

Q: If the total number of slots in a D.C machine is 25 and the total number of poles is 5, then what is…

A: Given: A DC machine with, Total number of slots = 25. The total number of poles = 5.

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.