Homework Help is Here – Start Your Trial Now!
Math
Statistics
You may need to use the appropriate appendix table or technology to answer this question. KALI, Inc., manufactures home appliances that are marketed under a variety of trade names. However, KALI does not manufacture every component used in its products. Several components are purchased directly from suppliers. For example, one of the components that KALI purchases for use in home air conditioners is an overload protector, a device that turns off the compressor if it overheats. The compressor can be seriously damaged if the overload protector does not function properly, and therefore KALI is concerned about the quality of the overload protectors. One way to ensure quality would be to test every component received through an approach known as 100% inspection. However, to determine proper functioning of an overload protector, the device must be subjected to time-consuming and expensive tests, and KALI cannot justify testing every overload protector it receives. Instead, KALI uses an acceptance sampling plan to monitor the quality of the overload protectors. The acceptance sampling plan requires that KALI's quality control inspectors select and test a sample of overload protectors from each shipment. If very few defective units are found in the sample, the lot is probably of good quality and should be accepted. However, if a large number of defective units are found in the sample, the lot is probably of poor quality and should be rejected. The quality control manager requested a producer's risk of 0.10 when po was 0.04 and a consumer's risk of 0.20 when p₁ was 0.15. Consider the acceptance sampling plan based on a sample size of 20 and an acceptance number of 1. Answer the following questions. (a) What is the producer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) X (b) What is the consumer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) 0352 x (c) Does the n = 20, c = 1 sampling plan satisfy the risks requested by the quality control manager? Discuss. (Select all that apply.) The producer's risk is acceptable since it is less than 0.10. The producer's risk is not acceptable since it is greater than 0.10. The consumer's risk is acceptable since it is less than 0.20. The consumer's risk is not acceptable since it is greater than 0.20.

You may need to use the appropriate appendix table or technology to answer this question. KALI, Inc., manufactures home appliances that are marketed under a variety of trade names. However, KALI does not manufacture every component used in its products. Several components are purchased directly from suppliers. For example, one of the components that KALI purchases for use in home air conditioners is an overload protector, a device that turns off the compressor if it overheats. The compressor can be seriously damaged if the overload protector does not function properly, and therefore KALI is concerned about the quality of the overload protectors. One way to ensure quality would be to test every component received through an approach known as 100% inspection. However, to determine proper functioning of an overload protector, the device must be subjected to time-consuming and expensive tests, and KALI cannot justify testing every overload protector it receives. Instead, KALI uses an acceptance sampling plan to monitor the quality of the overload protectors. The acceptance sampling plan requires that KALI's quality control inspectors select and test a sample of overload protectors from each shipment. If very few defective units are found in the sample, the lot is probably of good quality and should be accepted. However, if a large number of defective units are found in the sample, the lot is probably of poor quality and should be rejected. The quality control manager requested a producer's risk of 0.10 when po was 0.04 and a consumer's risk of 0.20 when p₁ was 0.15. Consider the acceptance sampling plan based on a sample size of 20 and an acceptance number of 1. Answer the following questions. (a) What is the producer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) X (b) What is the consumer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) 0352 x (c) Does the n = 20, c = 1 sampling plan satisfy the risks requested by the quality control manager? Discuss. (Select all that apply.) The producer's risk is acceptable since it is less than 0.10. The producer's risk is not acceptable since it is greater than 0.10. The consumer's risk is acceptable since it is less than 0.20. The consumer's risk is not acceptable since it is greater than 0.20.

MATLAB: An Introduction with Applications
MATLAB: An Introduction with Applications
6th Edition
ISBN:9781119256830
Author:Amos Gilat
Publisher:Amos Gilat
Chapter1: Starting With Matlab
Section: Chapter Questions
Problem 1P
See similar textbooks
icon
Related questions
Question
You may need to use the appropriate appendix table or technology to answer this question. KALI, Inc., manufactures home appliances that are marketed under a variety of trade names. However, KALI does not manufacture every component used in its products. Several components are purchased directly from suppliers. For example, one of the components that KALI purchases for use in home air conditioners is an overload protector, a device that turns off the compressor if it overheats. The compressor can be seriously damaged if the overload protector does not function properly, and therefore KALI is concerned about the quality of the overload protectors. One way to ensure quality would be to test every component received through an approach known as 100% inspection. However, to determine proper functioning of an overload protector, the device must be subjected to time-consuming and expensive tests, and KALI cannot justify testing every overload protector it receives. Instead, KALI uses an acceptance sampling plan to monitor the quality of the overload protectors. The acceptance sampling plan requires that KALI's quality control inspectors select and test a sample of overload protectors from each shipment. If very few defective units are found in the sample, the lot is probably of good quality and should be accepted. However, if a large number of defective units are found in the sample, the lot is probably of poor quality and should be rejected. The quality control manager requested a producer's risk of 0.10 when po was 0.04 and a consumer's risk of 0.20 when p₁ was 0.15. Consider the acceptance sampling plan based on a sample size of 20 and an acceptance number of 1. Answer the following questions. (a) What is the producer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) X (b) What is the consumer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) .0352 X (c) Does the n = 20, c = 1 sampling plan satisfy the risks requested by the quality control manager? Discuss. (Select all that apply.) The producer's risk is acceptable since it is less than 0.10. The producer's risk is not acceptable since it is greater than 0.10. The consumer's risk is acceptable since it is less than 0.20. The consumer's risk is not acceptable since it is greater than 0.20.
Transcribed Image Text:You may need to use the appropriate appendix table or technology to answer this question. KALI, Inc., manufactures home appliances that are marketed under a variety of trade names. However, KALI does not manufacture every component used in its products. Several components are purchased directly from suppliers. For example, one of the components that KALI purchases for use in home air conditioners is an overload protector, a device that turns off the compressor if it overheats. The compressor can be seriously damaged if the overload protector does not function properly, and therefore KALI is concerned about the quality of the overload protectors. One way to ensure quality would be to test every component received through an approach known as 100% inspection. However, to determine proper functioning of an overload protector, the device must be subjected to time-consuming and expensive tests, and KALI cannot justify testing every overload protector it receives. Instead, KALI uses an acceptance sampling plan to monitor the quality of the overload protectors. The acceptance sampling plan requires that KALI's quality control inspectors select and test a sample of overload protectors from each shipment. If very few defective units are found in the sample, the lot is probably of good quality and should be accepted. However, if a large number of defective units are found in the sample, the lot is probably of poor quality and should be rejected. The quality control manager requested a producer's risk of 0.10 when po was 0.04 and a consumer's risk of 0.20 when p₁ was 0.15. Consider the acceptance sampling plan based on a sample size of 20 and an acceptance number of 1. Answer the following questions. (a) What is the producer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) X (b) What is the consumer's risk for the n = 20, c = 1 sampling plan? (Round your answer to four decimal places.) .0352 X (c) Does the n = 20, c = 1 sampling plan satisfy the risks requested by the quality control manager? Discuss. (Select all that apply.) The producer's risk is acceptable since it is less than 0.10. The producer's risk is not acceptable since it is greater than 0.10. The consumer's risk is acceptable since it is less than 0.20. The consumer's risk is not acceptable since it is greater than 0.20.
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 5 steps with 9 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
MATLAB: An Introduction with Applications
MATLAB: An Introduction with Applications
Statistics
ISBN:
9781119256830
Author:
Amos Gilat
Publisher:
John Wiley & Sons Inc
Probability and Statistics for Engineering and th…
Probability and Statistics for Engineering and th…
Statistics
ISBN:
9781305251809
Author:
Jay L. Devore
Publisher:
Cengage Learning
Statistics for The Behavioral Sciences (MindTap C…
Statistics for The Behavioral Sciences (MindTap C…
Statistics
ISBN:
9781305504912
Author:
Frederick J Gravetter, Larry B. Wallnau
Publisher:
Cengage Learning
Elementary Statistics: Picturing the World (7th E…
Elementary Statistics: Picturing the World (7th E…
Statistics
ISBN:
9780134683416
Author:
Ron Larson, Betsy Farber
Publisher:
PEARSON
The Basic Practice of Statistics
The Basic Practice of Statistics
Statistics
ISBN:
9781319042578
Author:
David S. Moore, William I. Notz, Michael A. Fligner
Publisher:
W. H. Freeman
Introduction to the Practice of Statistics
Introduction to the Practice of Statistics
Statistics
ISBN:
9781319013387
Author:
David S. Moore, George P. McCabe, Bruce A. Craig
Publisher:
W. H. Freeman
SEE MORE TEXTBOOKS