You go to the gym to ride a stationary bicycle. The bicycle uses a large wheel to create resistance for your exercise. The wheel consists of some small spokes (we’ll ignore the spokes) and a hollow cylinder with an inner radius of 12cm, an outer radius of 35cm, and a mass of 48.9kg. You start with the bike not moving and peddle at a constant acceleration for 10sec to accelerate the wheel up to 36rad s . 3) What was the angular acceleration? 4) How much torque did you apply to the wheel? With the bike’s wheel spinning at 36rad s you decide to turn up the resistance to get a good workout. 5) If the bike is operated at a power level of 250W of resistance f

You go to the gym to ride a stationary bicycle. The bicycle uses a large wheel to create resistance for your exercise. The wheel consists of some small spokes (we’ll ignore the spokes) and a hollow cylinder with an inner radius of 12cm, an outer radius of 35cm, and a mass of 48.9kg. You start with the bike not moving and peddle at a constant acceleration for 10sec to accelerate the wheel up to 36rad s . 3) What was the angular acceleration? 4) How much torque did you apply to the wheel? With the bike’s wheel spinning at 36rad s you decide to turn up the resistance to get a good workout. 5) If the bike is operated at a power level of 250W of resistance f

Similar questions

In the figure, three 0.10 kg particles have been glued to a rod of length L = 11 cm and negligible mass and can rotate around a perpendicular axis through point O at one end. How much work is required to change the rotational rate (a) from 0 to 20.0 rad/s, (b) from 20.0 rad/s to 40.0 rad/s, and (c) from 40.0 rad/s to 60.0 rad/s? (d) What is the slope of a plot of the assembly's kinetic energy (in joules) versus the square of its rotation rate (in radians-squared per second-squared)? Axis -P--P-- P- (a) Number i Units (b) Number i Units (c) Number i Units (d) Number i Units
Refer to the question below.
1. A circular object of radius R starts from rest and rolls down an incline of M, I height H without slipping. The object has a mass M, a moment of inertia / and a radius R. We go through the steps in finding the speed of the object at the bottom of the incline below, a. What is the total mechanical energy of the object at the top of the incline? Write your answer in terms of I, M, R, H and/or g. b. What is the total mechanical energy at the bottom of the incline in terms of the speed v and the givens? Use the relation v = wR to eliminate the angular speed from your expression. Check that your expression has the correct dimensions. Your final expression should only contain v, I, M, R and/or g. When an object rolls without slipping, the point in contact with the ground is at rest. Therefore, the friction the mechanical energy C. force has displacer work, conserved. Use conservation of mechanical energy to find the speed v of the object at the bottom of the hill in terms of I, R, M,H…
In orbit mechanics, the angular momentum is also an important quantity governing the satellite's motion. Assume planar motion, a satellite is orbiting around Earth center within a fixed plane. Thus it's motion is completely described by the distance r and the angle (relative to some reference direction). êo 0 (center of Earth) êr PO.. P (satellite) satellite's trajectory Obtain the satellite's angular momentum with respect to Earth center. For spacecrafts, the angular momentum (h) is h = Fx, it is independent of mass. What is the magnitude of h?
Computation. Consider a frictionless flywheel in the shape of a uniform solid disk of radius 1.8 m. Calculate its mass if it takes 7.3 kJ of work to spin up the flywheel from rest to 548 rpm. [Tip: Be careful with units.] M = kg O Search Record your numerical answer below, assuming three significant figures. Remember to include a "-" as necessary. Ca 4 @
Question is on the picture
this is the introductory question to our new chapter and my professor didn’t list any formulas to use for certain question types and i’m just really stuck on this one
What is the speed of a point on the rim?
Please help showing how to solve this question. According to Canvas, the answer should be 1.367 m/s.
Consider a phonograph with a diameter of 0.6 m and a rotational speed of 33 RPM. Answer the following questions. What is its radius in m?What is its rotational speed in rad/s?What is the tangential speed on the phonograph's outer edge in m/s?What is the tangential speed at the center of the phonograph in m/s?What is the tangential speed halfway out to the edge of the phonograph?
When installing a new MSA cylinder into the harness, slide it thru until the cylinder is resting near or on the bumpers. How far should we rotate the cylinder so the cylinder gauge is face up?
Arithmetic question. Write only the final value of the answer. Suppose you did the rotational dynamics labs with a 200g solid sphere. The sphere was placed at rest at the 100cm mark on the track which is inclined at 150 angle with the table. What is the translational kinetic energy in (J) of the sphere as it leaves 0 mark of the track? Write your answer with TWO decimal places.