You combine 50g of ice at -10oC with 150g of liquid water at 75oC. After a few minutes, you measure the final equilibrium temperature of all of the H2O to be 35.1 oC. Use this information to “experimentally” determine the heat of transformation of water, Lfusion. cwater=4190 J/kgK, cice=2090 J/kgK Show all of your work and compare to the accepted value Lfusion=3.33x105 J/kg.

You combine 50g of ice at -10oC with 150g of liquid water at 75oC. After a few minutes, you measure the final equilibrium temperature of all of the H2O to be 35.1 oC. Use this information to “experimentally” determine the heat of transformation of water, Lfusion. cwater=4190 J/kgK, cice=2090 J/kgK Show all of your work and compare to the accepted value Lfusion=3.33x105 J/kg.

Similar questions

Consider a 0.16-kg piece of ice starting at -21°C. Hint a. How much heat transfer is necessary to raise the temperature of the ice to 142°C, including the energy needed for phase changes? Total heat transfer of kJ is necessary. b. How much time is required for each stage, assuming a constant 16 kJ/s rate of heat transfer? a. To heat up the ice to the melting point, seconds of time is necessary. b. To melt all the ice into water at the melting point, seconds of time is necessary. c. To heat up the water to the boiling point, seconds of time is necessary. d. To boil all the water into steam at the boiling point, seconds of time is necessary. e. To heat up the steam to the final temperature, seconds of time is necessary.
1 cal = 4.184 J, specific heat of iron = 0.45 J/g°C 1. If 2087.5 kcal of chemical energy is converted to mechanical energy and then electrical energy, how many kcal and joules of electrical energy is available? Explain. 2. a) Define the term, state function. ( one of the wo assmptions made for this model, (6 (amiog o) sbam od anoizulonoo ntw bas bovoado o Jominoqo brohadut eom3 sdinoesC b) Give THREE examples of state functions. (
In the model bridge in the previous video, say the model is made out of copper and it is 1 meter long at room temperature, 25 Celsius. The model is heated to a temperature of 50 Celsius, and the expansion measured on the dial indicator is 0.4125 mm (this is 412.5 * 10^-6 meters or 412.5 µm). Using that information, calculate an experimental value of the thermal expansion coefficient in copper. Please use the formula from the video: AL = L.a.AT (the video explains each term) The expansion is so small that it is traditionally measured in parts per million. The answer for a can then be reported as x 10^-6 per degree Celsius. Report your answer as the number of millionths (that is, if you were to fill in the blank.) Your answer should be between 0 and 100.
What is the correct answer to this problem? Some people got about 360J and others got around 570J, I really need help on figuring this out because it's really confusing me...
An ideal gas is confined within a thermally isolated cylinder. It consists of N atoms initially at a pressure of p0. A movable piston seals the right end of the cylinder, as shown in the figure. (Figure 1)A given amount of heat Q is slowly added to the gas, while the piston allows the gas to expand in such a way that the gas's temperature remains constant at T0. A) As heat is added, the pressure in this gas __________. increases decreases remains constant cannot be determined B) Is the internal energy of the gas the same before and after Q is added? yes no C) Does the second law of thermodynamics forbid converting all of the absorbed heat Q into work done by the piston? yes no D) The (Kelvin-Planck statement of the) second law of thermodynamics reads as follows:It is impossible for an engine working in a cycle to produce no other effect than that of extracting heat from a reservoir and performing an equivalent amount of work.The phrase "in a…
The temperature at state A is 20ºC, that is 293 K. What is the heat (Q) for process D to B, in MJ (MegaJoules)? (Hint: What is the change in thermal energy and work done by the gas for this process?)
Can you please answer number 3 and show all of the steps
3 of 4 A stainless-steel-bottomed kettle, its bottom 25 cm in diameter and 1.6 mm thick, sits on a burner. The kettle holds boiling water, and energy flows into the water from the kettle bottom at 800 W. Review I Constants I Periodic Tabl Part A What is the temperature of the bottom surface of the kettle? Thermal conductivity of stainless steel is 14 W/(m K). Express your answer using four significant figures. VO AEO ? T = 102.65 °C Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Review your calculations and make sure you round to 4 significant figures in the last step. Ne Provide Feedback
QUESTION 16 The temperature at state A is 20.0°C, that is 293 K. During the last test, you have found the temperature at state D is 73.0 K and n = 164 moles for this monatomic ideal gas. What is the change in thermal energy for process A to D, in MJ (MegaJoules)? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. p (atm) 5 4 3 2 1 0 A D 1 2 3 4 B 5 → V (m³)
The temperature at state A is 20.0°C, that is 293 K. During the last test, you have found the temperature at state D is 73.0 K and n = 164 moles for this monatomic ideal gas. What is the change in thermal energy for process A to D, in MJ (MegaJoules)? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. P (atm) 4 3 ID B +V (m) 4 5
D Copper, tin, shmian, plas because metals are good conductors of beat and transfer heat faster. Kinetic energy in the form of heat increases the motion of the molecules. Regions B and D of heating curve represent segments of the curve where heat is being added, but the temperature is not changing. E C MIN MIN NOI C CO Which of the following is the BEST explanation for regions B and D of the curve and why? The substance beazes or condesses because it is undergoing an exothermic phase change. The substance melts or evaporates because it is undergoing an endothermic phase change. The substance sublimes or deposits because it is undergoing an exothermic phase change. The substance freezes or evaporates because it is undergoing an endothermic phase change. Question 12 The image depicts the heating curve for water. 2615 words [X O Accessibility: Unavailable 2 11 W I We're startin
A 58-kg cross-country skier glides over snow as in the figure below. The coefficient of friction between skis and snow is 0.24. Assume all the snow beneath her skis is at 0°C and that all the internal energy generated by friction is added to snow, which sticks to her skis until it melts. How far would she have to ski to melt 1.5 kg of snow? Your incorrect answer may have resulted from roundoff error. Make sure you keep extra significant figures in intermediate steps of your calculation. m Need Help? Read It Master it