You are working as an engineer a company. During an energy audit, you realize that your company has a 40 kw transformer that is connected all the time. While inspecting the transformer, you calculate the core losses from the device to be approximately 5% of its rated capacity. Assume that the electrical costs are 10 C/kWh and 10 USD/KW/month of peak demand, that the average building use is 12 h/month, and that the average month has 720 hours. Estimate the annual cost savings from installing a switch that would energize the transformer only when the building was being used. The transformer is used h/month, and it can be turned off for the remaining of the month. That is h/month. That means the transformer can be turned off for h/year. The core losses from the tansformer is kW. Installing a switch to turn on the transformer only when the building is used results: Annual energy savings of kWh/year. Annual cost savings of USD/year. Does it make sense to use this strategy?

You are working as an engineer a company. During an energy audit, you realize that your company has a 40 kw transformer that is connected all the time. While inspecting the transformer, you calculate the core losses from the device to be approximately 5% of its rated capacity. Assume that the electrical costs are 10 C/kWh and 10 USD/KW/month of peak demand, that the average building use is 12 h/month, and that the average month has 720 hours. Estimate the annual cost savings from installing a switch that would energize the transformer only when the building was being used. The transformer is used h/month, and it can be turned off for the remaining of the month. That is h/month. That means the transformer can be turned off for h/year. The core losses from the tansformer is kW. Installing a switch to turn on the transformer only when the building is used results: Annual energy savings of kWh/year. Annual cost savings of USD/year. Does it make sense to use this strategy?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the level of the peak voltage at the secondary 1 (Vsecondary 1) and secondary 2 (Vsecondary 2) of the transformer shown below during the negative half cycle of the input voltage? No need to show your solution. Just write your numeric answer on the space provided below. ... Si 220 V 60 Hz ODeg 1.2kn V. 9:1 Si
i need the answer quickly
Is it possible have some help with this question, I get 75v for secondary emf and 0.5amps as secondary current!! thanks
a device has an average power rating of 1200W and deisgn to operate 250V rms line. detrmine the effective resistance if the power socket available has 115V rms line and uses a step up ideal transformer from 115V to 250V.
A 270 kVA transformer has primary and secondary winding resistances of 0.6Ω, and 0.0016Ωrespectively. The iron loss is 2.25 KW and the primary and secondary voltages are 7kV and 320 Vrespectively. If the power factor of the load is 0.6 lag, find the efficiency of the transformer for 20% of fullload.
Electrical Machines 2.4a please round off to 2 decimal places
Find the primary current (i1) in the following ideal transformer
Calculate the percent voltage drop in a 500 KVA transformer having 2% resistance and 4% reactance when delivering 400 KVA at 0.8 pf lagging.
Problem 1 The primary resistance of a 440/110-V transformer is 0.50 and the secondary resistance is 0.04 02. When 440 V is applied to the primary and secondary is left open-circuited, 200 W is drawn from the supply. Find the secondary current which will give maximum efficiency and calculate this efficiency for a load having unity power factor.
A 310 kVA transformer has a primary winding resistance of 0.65 and a secondary winding resistance of. 0.001 Q. The iron loss is 3.5 kW and the primary and secondary voltages are 3 kV and 240 V respectively. If the power factor of the load is 0.8,then determine the efficiency of the transformer on 75 % load. 11 12 Pc Efficiency Finish rev Windows
-5V 3.3LN 6,8 S2 lov D. D3 +SV Do, Dz, D3 are i deal diodes. Which ane onloff? dio des