You are tasked to layout a cross-flow heat exchanger where both fluids remair unmixed. Unused engine oil is cooled at a flow rate of 3 kg/s. The oil enters th heat exchanger at 85.5°C and is cooled to 45°C. Water is used as the cooling medium at a flow rate of 2 kg/s, entering at 40°C and exiting at 60°C. The flov conditions in this heat exchanger yield the following convective heat transfer coefficients: h; = 8,000 W/m²/K and h, = 15,000 W/m²/K. Determine the following: 1. What is the area required to achieve the proposed performance? 2. During the design process it is recognized that the oil will cause fouling. Th fouling coefficient is assumed to be 9.00*10-5 m²*K/W. How much larger will the area have to be to yield the same performance as in the clean state from part a?

You are tasked to layout a cross-flow heat exchanger where both fluids remair unmixed. Unused engine oil is cooled at a flow rate of 3 kg/s. The oil enters th heat exchanger at 85.5°C and is cooled to 45°C. Water is used as the cooling medium at a flow rate of 2 kg/s, entering at 40°C and exiting at 60°C. The flov conditions in this heat exchanger yield the following convective heat transfer coefficients: h; = 8,000 W/m²/K and h, = 15,000 W/m²/K. Determine the following: 1. What is the area required to achieve the proposed performance? 2. During the design process it is recognized that the oil will cause fouling. Th fouling coefficient is assumed to be 9.0010-5 m²K/W. How much larger will the area have to be to yield the same performance as in the clean state from part a?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hello Sir,Good Evening. I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice. Thank You "Explain the equation used to calculate the heat flux of a counter flow type heat exchanger with a fouling factor using the LMTD concept. Write down the equations involved"
Provide a technical design outlining the ideal refrigerant and operating parameters for a three-stage closed-type cascade refrigeration system that will run with a 150TOR load at -40°C evaporator and 65°C condensing temperatures. Imagine that your isentropic compression is 74% effective.Draw the engaging temperature as well so that the heat exchange interfaces differ by 5°C. Please draw detailed. explain Please. It would be a great help.
I need answer in 1hr do it fast. A shell-and-tube heat exchanger is set at the one shell pass and two tube passes. Hot air enters the shell at 90°C, and leaves at 50°C, whose mass flow rate is 5 kg/s. Cold water enters the tube at 23°C, whose flow rate is 3 kg/s. What is the water outlet temperature? What is the overall UA of the heat exchanger? a) Draw the problem diagram. b) List all required properties and equations to solve this problem. c) Solve the problem
show mathematically how the heat transfer coefficient on the boiler side changes with 50% increase in mass flow rate for phase, unchanging heat transfer and turbulent flow on both sides of the tube boiler type heat exchanger and how the heat transfer coefficient by the pipe is affected by 50% increase in mass flow rate.
While thermodynamics deals with equilibrium states and changes from one equilibrium state to another heat transfer deals with systems that have Select one: O a. Fluid equilibrium b. None of the above c. Mechanic equilibrium d. Thermal equilibrium
Show complete solution and illustration please.
Task (1) A. You were asked to design and manufacture a plate heat exchanger, as shown in the figure, to be used in transferring heat from hot water to cold water. Which material (copper, aluminium or polyethylene) will you choose to manufacture the inner plates of the heat exchanger to obtain the highest heat transfer? Give reason for your choice. B. Will the device be lighter in weight if it is made of copper, aluminium or polyethylene? Explain your answer. C. After you completed manufacturing the heat exchanger, you noticed that its outer surface is conductive to electricity, which may be dangerous during operation. what can you do to insulate it? D. Explain two types of degradation that could happen in the heat exchanger and discuss how to prevent them? E. Briefly explain one of the degradation types in polymers.