4 You are given a PN junction where the withdoping of NA=1017cm-3 and ND=2x1015cm-3. The band diagram of the PN junction atthermal equilibrium is given in the figurebelow.:AEcpEcnEfENPEynWhat is the carrier concentration at point "A"above the energy level ECn? (use scientificnotation, e.g. 1e17 for 101).What is the carrier concentration at point "A"above the energy level Ecp?

According to the question, we need to find the carrier concentration at point A above the energy…

Answered: You are given a PN junction where the…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
A 20-V-rms 60-Hz ac source is in series with an ideal diode and a 100-Ω resistance. Determine the peak current and PIV for the diode.
The input voltage (vin) of the following circuit is a sinusoidal signal with an amplitude of 2Vrms,consider a silicon diode.graph the output voltage ?? and the current across the resistor.
please label the questions
use a P-N junction ideal diode to simulate a circuit measure and plot its I-V characteristics as well as its forward characteristics. assume breakdown voltage of around 6V for your calculations. I have added my multisim design with IV graph of the diode. I need : the large signal piece wise linear parameters of the diode. and for the plot do the theoretical calculations for at least one point on the curve and mark it on the curve This peoblem has other part that I will send when the expert answered this part. Tnx
The circuit below has a variable voltage vin as its input. We are interested in Vout as a function of Vin. In other words, if we vary the value of the voltage source vin, what will be the effect on the voltage Vout? The steps below will help you to investigate this question, and your answers will form the basis for a new design. Assume that the diode can be sufficiently modelled as simple diode with forward voltage of 0.7 V (you do not need Shockley's equation). Vin 100Ω M Vf = 0.7 V 2 V V out
A diode with n =1.6 conducts 45 mA at 0.75V at room temperature. Find the saturation current Is at room temperature (using the exponential model).
For the diode circuit to the right 8002 a V 1002 b 40mA 0.001V' a) To the left of points a and b, find the load-line relation by expressing the current, I with voltage, V. HINT: Write KCL equation for the circuit diagram and write I in terms of V from that KCL equation. This will be your load-line equation. b) Assume the diode has the following characteristic, using the load-line relation you found in (a), determine the operating voltage, V and current, I for the circuit. ip (mA) 20 15 10 5 Vp (V) 3.0 0.5 '1.0 1.5 2.0 2.5
Helli. I only need the last part. Plotting power vs voltage if used as a solar cell and give the definition of fill factor. Tnx
A shunt regulator.( Need only handwritten solution please otherwise downvote).
4. A voltage regulator circuit is shown on the right. The resistor value is chosen to obtain an output voltage (across the diode) of 0.7V. Use the diode small-signal model to determine the change in the output voltage when the supply voltage, V+, changes by IV. (This quantity is known as the line regulation and is generally expressed in mV/V) Hint: The answer will be only a function of V+ V+ ▷ R + Vo
Given a circuit composed of a dc voltage source with its positive terminal of 10V connected in series to a 1Kohms limiting resistor and the anode of a diode. The cathode of the diode is connected to ground. Assume that the small forward dynamic resistance of the diode is 10ohms at the determined value of forward current. Use the 3rd approximation (complete diode model ) to determine the voltage across the limiting resistor. Draw the circuit and show your solution/s.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

You are given a PN junction where the with doping of NA=10o17cm-3 and Np=2x1015cm- 3. The band diagram of the PN junction at thermal equilibrium is given in the figure below.