You are drilling an artesian well in a steeped sloped region. You know from previous hydrogeological maps that several springs have been documented altitudes of 1100 - 1110 m. What would you expect if you drill a deep well at 1050m altitude?

You are drilling an artesian well in a steeped sloped region. You know from previous hydrogeological maps that several springs have been documented altitudes of 1100 - 1110 m. What would you expect if you drill a deep well at 1050m altitude?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give me right solution according to the question. Urgent please A 20-cm diameter well completely penetrates a confined aquifer of permeability 0.088 cm/sec. The length of the aquifer is 34 m. When pumping was kept constant at 78 L/sec, the drawdown at an observation well, 112 meters from the pumping well, was found to be 0.79 meters. Determine the drawdown at the face of the pumping well (in meters).
A well is pumping at an unknown, steady rate in a confined aquifer. Near the pumping well are two observation wells; observation well A is located 8m from the pumping well and B is located 24m from the pump- ing well. The heads in these wells are hA = 134.20 and hB = 134.28 m. You know from prior pumping tests of the well that the well and the observation wells are screened in a confined aquifer with transmissivity T = 1200 m2/day. Assuming that without the well pumping there would be no hydraulic gradient at all, what is the pumping rate of the well?
14. Yuri wants to determine the permeability of an aquifer. The aquifer has a test well 300-mm in diameter with two observation wells. A pumping test was conducted for 24 hours with the discharge being held constant at 5618.7 m^3/day. The first one, 88.43 meters from the test well, has a draw-down of 0.52 meters. The second one, 48 meters from the test well, has a draw-down of 1.48 meters.The static water table penetrates the well to a depth of 27 meters. Determine the radius of influence of the aquifer in meters. Round off to three decimal places.
Determine the hydraulic conductivity of a confined aquifer from which water is being pumped by a fully penetrating well. The aquifer is 100 ft thick ,and the well is being pumped at a rate of 1500 gal /min. Water surfaces in the two observation wells 700 ft and 70 ft from the pumped well are respectively 1 ft and 10 ft below their levels prior to the beginning of pumping
An artesian aquifer is being pumped by a fully penetrating well. As a consulting engineer, you are tasked to find the hydraulic conductivity of the aquifer. The aquifer is 100 ft thick and composed of medium sand. You pump the water from the production well at a steady-state pumping rate of 1000 gallons per minute (gpm). The drawdown at one observation well 50 ft away is 10 ft; in a second observation well 500 ft away it is 1 ft. The hydraulic conductivity you calculate is -gpd/square ft. Make sure you draw the Free Body Diagram (FBD).
(b) Water is to be pumped from a well. Two observations well were constructed to observe the head and drawdown of the groundwater. Calculate the steady flow pumping required for the well to maintain the head (hı and h2) as shown in Figure Q5. Ground surface Pumping well h2 = 90.6m h, = 85.3 m %3D Confining Layer , = 30m Confined depth = 40 m r2 = 100m Confined aquifer Bedrock Figure Q5: Location of observation wells and pumping well in confined aquifer
The static level of water table in an unconfined aquifer was 35m above the underlying impermeable stratum. A 75mm radius well, penetrating the aquifer to its full depth, was pumped at the rate of 28 liters per second. After several weeks of pumping, the drawdown in observation wells 20m and 50m from the well were 3m and 2.5m respectively, and the observed drawdowns were increasing very slowly. (B.Sc., UAE, 1989).a) Assuming equilibrium conditions, estimate the hydraulic conductivity and transmissivity of the aquifer.b) Estimate the drawdown just outside the pumped well.
A 30 cm diameter well completely 15 points penetrates a confined aquifer of permeability of 45 m/day. The thickness of the aquifer is 20 m. Under steady state of pumping the drawdown at the well found to be 3.0 m and the radius of influence was 300 m. Calculate the discharge of the well * Pumping well dia = 2r + Original piezometric surface Piezometric surface under pumping Aquiclude Flow Confined aquifer Aquiclude Well Operating in a Confined Aquifer 1.548 m^3/min 0.0258 m^3/min 0.258 m^3/min 0.0851 m^3/min
Design a well ( find the diameter and drawdown of well ) witch is penetrating in un confined aquifer with depth 12 m to discharge the water at rate 3 cumcs from a land , the hydraulic conductivity is 10 m/day , the storag coefficent of medium sand soil is 20 , the drawdown of testing well awy 510 m is 1 m ? Then explain your design . i need solutions in 30 minutes please
Hydrology engineering Q5. well with a radius of 0.5m , completely penetrates an unconfined aquifer of thickness 50m and K=30m/day .the well is pumped so the water level in the well remains at 40m above the bottom .Assuming that the pumping has essentially no effect on water table at R=500m ,what is the steady state discharge ?
B- A 20cm diameter well penetrates fully a confined aquifer of thickness 25m .when the well is pumped at a rate of 200 liters/ minute the drawdown in two observaƟons wells located at 10m and 100m distance from center of well are found to be 3.5m and 0.05 m respectively .calculate the hydraulic conductivity of the aquifer and the radius of influence and the drawdown in the well.?
An artesian well with a radius of 0.75 meters was constructed to pump water from a source with a confining unit height of 30 meters. Two observation wells are 200 meters and 1,500 meters away from the test well with corresponding drawdowns of 9 meters and 3 meters at a steady state. Water is pumped at a rate of 432,000 L/day. c) What is the value for the hydraulic conductivity d) The soil classification for the confining unit can be e) The transmissivity