y the help of a fan ,air is drawn through a pipe of diameter 0.5 m. The temperature of air is 20°c If the quantity flow is 4.5 m3 s' nd also the length of the pipe is 12m, with a friction issue of 0.005, verify the fan shaft power necessary, forwarding an mechanical fficiency of eighty percent Take air density as 1.2 kilogram m3 and viscousness as 1.8 x 10-3 N s m-2.

Q: I need parts 7, 8, and 9, answered pertaining to the print and instructions.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: Given the two views of a solid and an auxiliary reference plane, draw the auxiliary view and…

A: Draw Auxiliary view of the given figures.

Q: In the drilling process shown in Figure 1, there are which cylinders A and B are used to clamp the…

A:

Q: In the TRIM command, when selecting objects to trim, holding downthe <Shift> key: a. Allows…

A: By holding the <Shift> key while using the TRIM command, it will be inverted to the opposite…

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: I need parts 7, 8, and 9, answered pertaining to the print and instructions.

A: Hello. You have asked to solve question 7, 8 and 9 but, question 7 is not provided in the given…

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: what is the omega value? as per the professor, the IC is at b not a

A: Given: The velocity of the upper wire: →V=5.6 m/s It is right that the instantaneous center of…

Q: A single CNC code block may contain only one G command. OTrue O False

A: Answer: The given statement is True.

Q: In the drawing below, which feature control frame controls the form of datum feature A? L.006 A B 3…

A: Feature control frame is used to show or describe the condition and tolerances used in designing of…

Q: hy is incremental positioning usually used with an axis return?

A: The absolute coordinates system the reference each position on the work piece is same or origin…

Q: In a tap set, an intermediate tap is used to start a thread form in a drilled hole Select one: O…

A: The given statement is true.

Q: Based on the image above, if the +Z jog button is pressed, turning the dial to the left will cause…

A: following is the correct answer to the above question-

Q: How to perform zero point reset

A: Zero point reset is an introducing system for tenant discovery sensor that should be performed…

Q: Basic Conversions A solid flat disk is rotating in the counter-clockwise (or positive) direction.…

A: givenobject is at a distance r=1.3mangular velocity when θ=0, ωo=4rad/safter t= 1.57sec angular…

Q: Which of the following is true about machine home, part origin, and tool change position? (choose…

A: option  b and c is correct  part origin is set by the programmer. all subsequent relative programmed…

Q: -30- R-64 20 -10 (5.0) -50 -40 -30 -20 -10 10 10-

A: given:

Q: 3. What is the difference between Turn Coordinator and Turn and Slip Indicator?

A: the turn and slip indicator and turn coordInator are very similar.in fact , the turn and slip…

Q: 2.500 3.500 1.500 3.000 4X Ø.760-.790 +0.010M 1.500 1.500 01.000-1.030 A 0.060M

A: In the feature control frames on the drawing, there are three datum symbols. These symbols are given…

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.