Y = RV R₂ Vief We wish to have Vref = (4 ± 4%) V. We choose R₁ = (2210 ± 1%). 1. With the help of the voltage divider, give the expression of Vref as a function of Vcc, R₁ and R₂. 2. Calculate R₂ in such to respect the load book. 3. From the tolerance of Vref, find the interval of values of this voltage.

Y = RV R₂ Vief We wish to have Vref = (4 ± 4%) V. We choose R₁ = (2210 ± 1%). 1. With the help of the voltage divider, give the expression of Vref as a function of Vcc, R₁ and R₂. 2. Calculate R₂ in such to respect the load book. 3. From the tolerance of Vref, find the interval of values of this voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering ell Vdc = 24 v Vs(t) = 120 V RMs Problem 1: Given the half-wave rectifier with the DC source above a) If it is operating at 60 Hz, when there is a load current of 2 A, what is the value of the resistance across the load? b) What is the value of the inductor to achieve a load current that is less than 1 A. c) For the DC source, find the power absorbed d) For the resistor, find the power absorbed
2.48 With a 1-W load, the voltage at the terminals of a cer- tain voltage source is found to be 10.0 V; without the load, it rises to 10.2 V. Estimate vs and Rs. Hence, predict the voltage at the terminals of the source for the case of a 22-22 load.
Subject: Electronic s. Please ASAP
a) A single-phase uncontrolled bridge rectifier supplies a highly inductive load from a single- phase 50 Hz AC voltage source. By neglecting the effect of line inductance, the rectifier generates average output voltage and current values of 180 V and 6 A, respectively. Due to the highly inductive load, the current waveform is constant and ripple-free. However, when considering a line inductor of 5 mH, the average output current drops by 3%. i) With an aid of a circuit diagram, explain the reason behind the zero voltage across the rectifier's output during the commutation interval. ii) Calculate the commutation angle and the average voltage drop values.
J62 For the magnetically coupled circuit shown, find K J72 the values of coupling coe fficient "k" when the power at 100 resistance is equal to (40W) if Vs=5020°v. (Ans.: 0.279) Vs 4.672
4. From the figure shown which is series-parallel, the following values are: ID ohms in series with the parallel combination of 30 and DD ohms respectively. If the supply voltage is bD volts, find the following: a) equivalent resistance b)total current c)individual current d)current at 3D and D ohms only
A PMMC instrument has internal resistance of 0.63 kQ and gives full scale deflection for 31 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 64 V will be ohms. O a. 205.82 O b. -145.62 O c. 1434.52 O d. 101556.30
Write the application of super tension that have rating upto 33KV and what used for?
A battery is comprised of 4 cells connected in parallel, each cell has an EMF with 1.2V and an internal resistance of 0.55 ohm. There is no load connected to the terminals. Solve for Vterm.