X The rod, supported by thrust bearing at A and cable BC, is subjected to an 80 lb force. Draw a FBD suitable to find the reactions at A and B. Z A 6 ft F = 80 lb D 1.5 ft C B 1.5 ft

Q: Determine the components of the reactions at A and B

A:

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. 785 mm 27° 315 mm B 61°…

A:

Q: If the mass of the flowerpot is 65 kg, calculate the tension generated in every cable for…

A:

Q: Q2: Determine the reactions of fixed support at A 15 kN 7 kN/m 4 kN/m 60° A 3 m 3 m

A:

Q: What is the magnitude of the reaction at roller D if P = 8 kN and C is a pin connection? A 2.5 kN 4…

A: Given:Uniformly distributed load from A to C Point load between  C and D Pin joint at C

Q: For the frame shown in Figure, determine the reaction at A, B, and D. 80 kN/m 20 kN/m B 4 m 6 m

A:

Q: Q4 - Determine the reactions at the supports. 500 N/m www...... B 4 m 4 m 30

A:

Q: The spanner shown is used to rotate a shaft. A pin fits in a hole at A, while a flat, frictionless…

A: The objective of this problem is to find the component of the reaction at A in a direction…

Q: 100 Ibs 3. Determine the reactions at Points A and B for angle alpha = 60 degrees. 12 in.

A: Given data as per question The load applied =100 lbs Considering FBD of the system taking moment…

Q: 3/91 Determine the forces on the bearings A and B if a 30-lb force on the crank is required to…

A: To findDetermine the force on the bearings A and B.GivenForce, F = 30 lbConnecting rod length, l =…

Q: Question 3 (Type B): The 50 N force F is parallel to the y axis. Determine the components of the…

A: The force F is

Q: Compute the reactions at C and E

A: Given Below is the truss

Q: Find the reactions at support A. Z 5 kN/m 4m 7 kN/m B 777 5m C X

A: According to the given data in the question A Right angle bend beam ABC is Loaded with UDl load. We…

Q: Refer to the diagram. The roller at A is in a smooth slot. Determine the reactions at A and O.

A: for vertical equilibrium F1sin 55 + Ay = Ry1.258 * sin 55 + Ay = Ry   For Horizontal Equilibrium…

Q: Find the forces of each members and the reaction of in the truss.

A:

Q: Point D is held in equilibrium by the cables as shown. If the force of F is 305 lb, then what is the…

A: Point D is held in equilibrium by the cables as shown. If the force of F is 305 lb.To Find-The…

Q: Find the support reactions of the fixed point O. The Distance from B to A is 220 mm and the given…

A: Given- l=220mm=0.22m           force=110NDetermine- support reaction at point O

Q: Determine the moment reaction at B.

A:

Q: Determine the components of the reactions at D and E if the frame is loaded by a clockwise couple of…

A: (a) Consider the first case where a 150 N.m CW moment acts on the point A. Consider the free body…

Q: Find the support reactions at the ball and socket 3. support A and the tension, T1 and T2.

A: Given data: F=133 kNCoordinates of A=0, 0, 0Coordinates of B=0, 0, 9Coordinates of C=4, 3,…

Q: Suppose P = 2500 lb. From the frame below, determine the magnitude and direction of the vertical and…

A:

Q: P2 B. C 4 m D -3 m- -3 m- -3 m- -3 m-

A:

Q: Determine the reactions at supports A and B. A 500 lb/ft -6 ft 6 ft- 700 lb/ft -8 ft- 9 ft 6 ft

A: To find reactions at A and B

Q: 4" 4" 12 6" 4 7" A T 30 lb

A:

Q: Determine the support reactions of the member's shown.

A:

Q: C 2 m 3 m 4 m 52 kN 30° D B.

A:

Q: 1. The wheel loads on a jeep are given. Determine the distance x so that the reaction of the beam at…

A:

Q: Determine the magnitude of the reaction at support A, in lb. If: P = 314 lb, h = 13 in., A = 27 in.…

A:

Q: Q4. Determine the support reaction on the member. The collar at A is fixed to the member and can…

A:

Q: Find the reactions at the fixed support A given the distributed loads shown. (+)+ 1 = (d) 1 = su A y…

A: Step 1:Step 2: Step 3: Step 4:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.