x kg/s of moist air at 35°C dry bulb temperature and 20% RH is mixed with kg/s of moist air at 20°C and a humidity ratio of 0.015 kg/kgDA in an adiabatic mixing chamber. The temperature of the air after mixing is 30°C. Find the humidity ratio of air after mixing. Post mixing, a sensible heating load of 4kW is supplied to heat up the mixed air. Calculate the final temperature of mixed air at the heater. Assume the barometric pressure to be 101.325 kPa. Use Cpm = 1.005 kJ/kg.K. Psychrometric chart is not required.

x kg/s of moist air at 35°C dry bulb temperature and 20% RH is mixed with kg/s of moist air at 20°C and a humidity ratio of 0.015 kg/kgDA in an adiabatic mixing chamber. The temperature of the air after mixing is 30°C. Find the humidity ratio of air after mixing. Post mixing, a sensible heating load of 4kW is supplied to heat up the mixed air. Calculate the final temperature of mixed air at the heater. Assume the barometric pressure to be 101.325 kPa. Use Cpm = 1.005 kJ/kg.K. Psychrometric chart is not required.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3/Air washer was used to cool air entering at 35°C dry bulb and 50% relative humidity. The air leaves the air washer at 20°C dry bulb temperature. (A)Determine the moisture added per kg of dry air.(B)What is the efficiency of the air washer.(C)calculate *. the heat removed by the washer
PROBLEM: IIC - 12 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
An air handler supplies 2.36 m3 /sec at a temperature of 12°C. The air handler was designed for 0.5 m3 /sec of outside air at 32oC DB and 26°C WB. The remaining return air from the space is at 25°C DB and 55% relative humidity. What are the entering conditions of the air into the coil, in DB and WB? Air pressure is 101.325 kPa
Air at 90○F and 20% relative humidity is cooled to 75○F. Assuming standard atmospheric pressure when the inlet flow rate is 1500 ft3/min, what amount of thermodynamic conditions are needed to achieve the resulting temperature?
Required information Problem 14.108 - Cooling Tower Assessment NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The cooling water from the condenser of a power plant enters a wet cooling tower at 40°C at a rate of 91 kg/s. The water is cooled to 25°C in the cooling tower by air that enters the tower at 1 atm, 23°C, and 60 percent relative humidity and leaves saturated at 32°C. Neglect the power input to the fan. Use data from the psychrometric chart and tables. Problem 14.108.a - Cooling Tower Assessment Determine the volume flow rate of air into the cooling tower. m³/s. The volume flow rate of air is
Air enters a humidifier at 34.25°C and 30% RH. If the air leaves the humidifier at 70% RH. Determine: The exit dry-bulb temperature of the air in °C.The saturation effectiveness in %.
Can you make a schematic diagram for this problem? 600 lps of air at 30°C dry-bulb and 22°C wet-bulb temperatures is heated to a temperature of 45°C and enters the dryer. The air leaves the dryer adiabatically and its relative humidity is 70%. Determine: (a.) The water evaporated kg/hr; (b.) The volume air leaving the dryer in cu.m/min; and (c.) kJ requirement of the dryer per kg of water evaporated.
A bedroom is to be conditioned that the total heat load is 20 kW and the sensible heat ratio is 0.4. The room is to be maintained at 22°C DB and 55% relative humidity. The outside air condition is at 32°C DB and 23°C WB. The conditioned air from the reheater enters the room at 17°C. Determine the following: a. The percentage of recirculated air if the mass flow rate of water vapor in the mixture is 1 kg/min b. The refrigeration load TR c. The heat required in the reheater kW
Atmospheric air, which is a mixture of dry air and water vapour, is supplied into ducting with a cooling coil. Initially it has a relative humidity of 0.57, volumetric flow rate of 0.72 mis and temperature of 17°C. The atmospheric air is then passed over a cooling coil such that the temperature drops to 6°C. As this is below the dew point, the water vapour condensates after cooling coll and the air leaves in a saturated state. Assuming the barometric pressure of atmosphenic air to be 1.01325 bar, determine the folowing quantities in question parts () to (vi): (1) Partial pressure of water vapour in the air and water vapour mixture entering, Pul
Wet material, containing 215% moisture (dry basis) is to be dried at the rate of 1.5 kg/sec in a continuous dryer to give a product containing 5% moisture (wet basis). The drying medium consists of air heated to 373°K and containing water vapor equivalent to a partial pressure of 1.40 Kpa. The air leaves the dryer at 310°CK and 70% saturated. Calculate how much air will be required to remove the moisture. A. 213,233 kg/hr B. 177,142 kg/hr C. 177,242 kg/hr D. 198,234 kg/hr Solve and arrive the exact answer as it is given one of these choices. Include the units in the process Thanks!
Air at 35 m dry and 50 relative humidity enters a cooling coil at a rate of 500 (l/sec) and exits saturated at 23 m dry, calculate the cooling capacity of the coil (cooling belly)
Using a psychrometric diagram, describe the heating and humidification process from the following data. Initially the air was at a dry bulb temperature (DBT) of 30 ° C and RH60%. The air is heated to DBT 80 ° C. The heated air is then flowed through a humidifier to increase the RH to 25%. For this process, calculate,a. Change in absolute humidity of air from initial to final conditions = (kg water / kg air).b. The change in air enthalpy from initial to final conditions. = (kJ / kg air)