x coordinate. q=20kN/m F=14kN M=12kNm L1=1.2m L2=1.4m L3=1.3m L4=1.5m   Maximum value of bending torque Mmax = ??? Maximum position of bending moment x = ???   Use units (kN,m), Do not round the invoices in the intermediate stages, but only the final answer!

Q: Draw a shear force diagram Bending movement Diagram

A:

Q: Please write the problem on paper, I do not like it when it is typed out on the computer. Need help…

A:

Q: determine the magnitude of the couple forces

A: Moment of couple:- Moment of couple is defined as the two parallel forces with same magnitude but…

Q: Use the graphical method to draw shear froce and bending moment diagrams for the beam shown below…

A: Use the graphical method to draw shear froce and bending moment diagrams for the beam shown below…

Q: Determine the reactions at pin A and rollers B and C of the continuous beam shown below. Note:…

A: Draw the free-body diagram of the beam.

Q: Consider the frame shown in (Figure 1). Suppose that F-310 lb. Follow the sign convention. Figure 3f…

A:

Q: please help asap Find the forces in each member.

A: Write the vectors AD, BD and CD.…

Q: Part A The force F = (-6i+ 3j+ 14 k) N is applied to the block shown in (Eigure 1). Figure -3 m 2 D…

A:

Q: oblem 7: Non-circular cross section shaft related to torque problems are difficult to be solved…

A:

Q: peR) = F( 3*-37ti) 1. Write down the governing equation 2. State the boundary conditions 3. Solve…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1: Step 2:please give helpful rating  Step 3: Step 4:

Q: (c) Determine the 1st moment of area Q, of the top-half region A' (red shaded area) against z axis,…

A:

Q: The figure shows a cantilevered beam, subjected to a uniformly distributed (rectangular) 40 N/m…

A:

Q: 12-15. A torque wrench is used to tighten the nut on a bolt. If the dial indicates that a torque of…

A:

Q: Question 7 Consider the structure shown in (Figure 1). Suppose that F = 2400 N| • Part A Determine…

A: Moment couple (C) = F x perpendicular distance between the forces

Q: a=75 mm b=160 mm c=20 mm determine the moment of interia Y prime

A: Given Data

Q: 8KN 2KN am 3m

A: given; w=2kN/m

Q: Two identical 20-mm thick plates are bolted to the top and bottom flange to form the built-up beam.…

A:

Q: 1.An axial pull of 40000 N is acting on a bar consisting of three sections of length 30 cm,25 cm and…

A: Given data E=2x105mpaTo find1) Stress om each section2) Total extension

Q: Replace the force system acting on the beam by an equivalent resultant force and couple moment at…

A:

Q: Replace the force system acting on the beam by an equivalent force and couple moment at point A.…

A: According to the company's guidelines, When multiple questions are asked only first question has to…

Q: Please draw a FBD only for the circled yellow part known as a rubber base plate :) I don’t want the…

A:

Q: The magnitude of F₁ is 58.7 The angle for F₁ is 0₁ 909.36 XN X

A:

Q: Problem 4: Shigley 3-34 (modified) Assume that the car is in the middle of the bridge span for…

A:

Q: Suppose that F= 2400 N. • Part A Determine the resultant couple moment. Express your answer to three…

A: To calculate the resultant moment we are taking the moment about point B ... Given that F=2400N

Q: Consider the pipe assembly in (Figure 1). F₁ = {30i +40j-30k) N. F2 = {601 - 10j-15k} N. Figure 0.8…

A: The force applied is

Q: Consider the cutaway diagram provided above. Using this, identify and describe a structural…

A: Given:To find:Structures that carry bending.

Q: 14i+19j [N] is applied to the end of a rod extending from point A with coordinates (XA, YA) = (3.1,…

A:

Q: Live load on the deck = 70 psf Deck weight = 6 psf Beam weight = 8 lb/ft Column weight = 80 lb…

A:

Q: W₁ = 100 rad/s Not to scale 0₁ B = 50 mm BC = 125 mm Joints O₁, B and C are frictionless revolute…

A: Draw the acceleration polygon.From the drawn polygon,find angular acceleration of link 2 (link BC)…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.