X A dc motor, 4kw, 160 volts, 1650 rpm, separately excited with armature resistance 1 ohm. The motor is used to drive through reducer of = 12 If the required load torque is 16 N.M and speeds 1.5 rad/sec. [1] Calculate the voltage reduction to drive the motor in such a required load? [2] The voltages appear on the motor *

X A dc motor, 4kw, 160 volts, 1650 rpm, separately excited with armature resistance 1 ohm. The motor is used to drive through reducer of = 12 If the required load torque is 16 N.M and speeds 1.5 rad/sec. [1] Calculate the voltage reduction to drive the motor in such a required load? [2] The voltages appear on the motor *

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A four-pole DC shunt motor, 220 V, the number of conductors in the armature 1000, the typical winding coil, the motor draws 52 A, the magnetic flux per pole 0.02 Wb, the armature resistance 0.2 02, and shunt resistance 110 Q. Calculate motor speed.
A DC motor has the following specifications: 10 hp, 37.5 A, 230 V; flux / pole = 0.01 Wb, number of poles = 4, number of conductors = 666, number of parallel paths = 2. Armature resistance = 0.2672. The armature reaction is negligible and rotational losses are 600W. The motor operates from a 230V DC supply. If the motor runs at 1000 rpm, the output torque produced in (in Nm) is
H.W 1) A 4-pole, 500 V d.c. shunt motor has 720 wave-connected conductors on its armature. The full-load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 Q and the contact drop is 1 V per brush. Calculate the full-load speed of the motor. H.W 2) A d.c. series motor with series field, and armature resistance of 0.06 ohm and 0.04 ohm respectively is connected across 220 V mains. The armature takes 40 A, and its speed is 900 rpm. Determine its speed when the armature takes 75 A, and excitation is increased by 15% due to saturation.
answer all subparts please
A 240 V D.C. series motor takes the current of 10 A at normal running condition and the field resistance is 0.3 ohm. If Torque remains the same and it is shunted by same field resistance value then line current of motor is (estimated time 2 minutes) a.10 A b.20 A c.15 A d.5 A
A 400V, 60HZ, 6-pole wye connected , 30 induction motor draws 75KW with a line current of 100A. The core loss is 2KW, Friction and Windage loss is 1.2KW. The stator resistance between two terminals is 0.352. What is the efficiency if the motor runs at a slip of 2.5%?
15. What are the following statements are true for DC Motor? I. Motor converts Electrical Energy to Mechanical Energy II. Motor supply current to the armature winding III. Back EMF is lesser than the Supply voltage IV. Fleming's Right-hand rule a. I and II b. II and IV c. I,II and III d. I,II and IV
What is the name of the part of the DC machine that is made up of copper? O a. Armature winding O b. Magnetic Poles O c. Commutator O d. Brush
A 50 HP. 400 V. 4 pole, 1000 rpm. DC motor has flux per pole equal to 0.027 Wb. The armature having1600 conductors is wave connected. Calculate the gross torque when the motor takes 70 ampere.
Q2:= A 4-pole ,250V series motor has a wave Connected anmature with 1254 Canductors. The Flux per pole is 22 m wb when the motor is taking 50A. Ion and friction losses amount to Lkw. Amature resistance is o-202 and series field resistance is o.202 Calculate - (i) the speed C) the shaft torque (t) the efficiengl
1) A 4 pole, 220 V lap connected de shunt motor has 36 slots, each containing 16 conductors. It draws a current of 40 A from the supply. The field resistance and armature resistance are 110 2 and 0.1 S2 respectively. The motor develops an output power of 6 kW. The flux per pole is 40 mWb. Calculate (i) the speed (ii) torque developed by the armature and (iii) the shaft torque.
A 350 V shunt motor runs at it's normal speed of 720 r/min when the armature current is 90 A. The resistance of the armature is 0.3 ohm. Determine the following: (1) The kΦ1 of the motor. If armature current is 45 A and a resistance of 0.4 ohm is connected in series with the armature and the shunt field remaining constant determine the following: (2) The new kΦ2 of the motor. (3) The new speed of the motor in r/min If the current is 45 A and the shunt field is reduced to 75% of it's normal value by increasing resistance in the field circuit, determine the following: (4) The new kΦ2 of the motor. (5) The new speed of the motor in r/min