Write the voltage divider relation (Vout/Vin) for the circuit of Fig. L2.1. • Calculate the Thevenin and Norton equivalent of the circuit shown in Figure L2.2 as seen by R₂. LAB Part I: Voltage Dividers Construct a voltage divider circuit as shown in Fig. L2.1. Vin R₁ 1. Set Vin to 10V. 2. Choose R1 =4.7 K2, R2 = 6.8 KM2. R₂ ww Fig. L2.1. Voltage divider

Write the voltage divider relation (Vout/Vin) for the circuit of Fig. L2.1. • Calculate the Thevenin and Norton equivalent of the circuit shown in Figure L2.2 as seen by R₂. LAB Part I: Voltage Dividers Construct a voltage divider circuit as shown in Fig. L2.1. Vin R₁ 1. Set Vin to 10V. 2. Choose R1 =4.7 K2, R2 = 6.8 KM2. R₂ ww Fig. L2.1. Voltage divider

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown in Figure Q2a, find the current Iı , 2 , Ix, and the voltage VA, VB and Vo. Given that: Vsi and VGe are 0.7 V and 0.3V Ix 4 1ko 1ko VA 2ko VB Ge 12 Ge 2 V Ge Si 12 V 2k2 Vo 2 V Figure Q2a
q19) please need fast
R1 D1 D2 R2 V1 V3 R3 V2 Rj=120 Q, R2=10 Q and R3=200 2, Vi= 10V and V2=15V, Dị and D2 (forward voltage drop) VF=0.8V a) Using mesh analysis to analyze the given circuit, derive the voltage V3. b) What is the state operation of Di and D2?
question
Refer to the figure. Given 2RRL2 R2 = 3R2 – RL a) Design the power supply cireuit so that v; = 3r, when R. - 600 s2. b) Assume input voltage is 180 V. Which resistor in the circuit dissipates the most power? What is the power? c) Which resistor dissipates the least power? What is the power? R: ww- a R R RL by d ww- ww-
V1 = 50 V R1 = 4 ohms R2 = 4 ohms R3 = 8 ohms 1) Find voltage-delta across R1 in the circuit when using Thevenin method - short circuit to find Isc. 2) Find Thevenin resistor value, Rth. 3) calculate current-delta across R3 in the circuit when using Thevenin method - open circuit to find Vth. 4) find current-delta across R3 in the circuit when using Thevenin method - short circuit to find isc.
Yudit Fshatsion: Attempt 1 R1 Ru Voltmeter R2 The RCL bridge seen in the picture is used to determine the resistance Ru (resistor under test). For the supply voltage V we can use: Either a DC or an AC power supply, as long as the voltmeter can handle this type of voltage. Only an AC power supply since we need to provide a certain Vrms with high accuracy for precise measurements. The measurement cannot be performed, since RCL bridges should be made of resistors, capacitors and inductors connected together. Only a DC power supply, since AC power supplies will provide bipolar voltages.
PARALLEL CIRCUIT 1. Create the circuit shown in figure B. Measure and record Vah, Vbg, Vcf, Vde, 16k, 13k and 12k and Itotal. 3. Compute the total resistance. 4. Using the formula Rt=Vah/It, compute for the total resistance. 5. Record the results in table 2. 2. a d V2 R6 S6kΩ R5 R4 –12V 3kn 2kn Figure B g f e Table 2 Vah Vbg Vcf Vde It 16k 13k 12k Rah Measured Values Computed Values
Q1- For the circuit shown in figure 1 Calculate the value of 1₁,13,15,using Nodel or Mesh analysis or any role ?... Q2- For the circuit shown in figure 2 Calculate the value of ITOT & VRS?..... Figure 1 Figure 2 E₁ 60 v + 20 R1 4 k Ohm R2 16V 8kOhm R3 6 k Ohm 40 www 20 R4 4 k Ohm www 20 R5 2k Ohm R6 4 k Ohm R7 2k Ohm 20 .). E₂ 20 v R8 2k Ohm
Q3/ In the following figure, the first resistance (R1= 252) and the second resistance (R2= 1252), calculate: 1- The value of the resistance (R) when the bridge is in equilibrium (V=V2) and the value of the variable resistance (R 3 = 802). 2- The value of the variable resistance(R3)when it is(2V1=V2).
Please solve the problem and show the solution.
3.-Calculate the electrical currents already indicated with their respective label in the circuit, that is, the currents in each branch 11= 12= 13= Note. The current 11 passes only through R1, and R3, 12 passes only through R4, and 13 passes through R2 and Rs. Draw the polarity to active, passive elements, nodes and meshes. R₁=2 Q ww V₁=10 V a V2=6 V ry R4=3 Q R3=4 Q R2=40 ww www b www V3=4 V R5=2 Q