Write a program to simulate a gate barrier system. Use the following program flow: 1. Gate is in an idle state waiting for a car 2. If a car is present, the gate will open as shown in the figure. 3. The gate will stay open for 5sec. If there is not a car present, the gate will close. 4. While closing, if a car arrives the gate will immediately return to the opening mode. You should use PCO to simulate the sensor that detects the cars. A '1' at PCO simulates a car present and a '0' represents the absence of a car. Make sure to enable pullup resistors on PCO and use bitmasking to read its value. PCO or pin 37 Wire Car not present PCO or pin 37 Not Connected +5 V Car present Wire PCO or pin 37 Connected to +5 V Close Open For the gate, you will

Write a program to simulate a gate barrier system. Use the following program flow: 1. Gate is in an idle state waiting for a car 2. If a car is present, the gate will open as shown in the figure. 3. The gate will stay open for 5sec. If there is not a car present, the gate will close. 4. While closing, if a car arrives the gate will immediately return to the opening mode. You should use PCO to simulate the sensor that detects the cars. A '1' at PCO simulates a car present and a '0' represents the absence of a car. Make sure to enable pullup resistors on PCO and use bitmasking to read its value. PCO or pin 37 Wire Car not present PCO or pin 37 Not Connected +5 V Car present Wire PCO or pin 37 Connected to +5 V Close Open For the gate, you will

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

28. A 3 phase, 1 MVA, 11 kV, four-pole, 50 Hz, star-connected synchronous machine has negligible R and X, is 100 /phase at the rated voltage. The machine is operating as a motor connected to an infinite bus with the rated MVA at 0.85 PF lagging. (a) Find per phase back EMF of the motor. (b) Find the net torque developed in the motor. (c) What is the percentage increase or decrease of the field current is needed to make the power factor unity for the machine when power delivered remains unchanged?
Short answer please please please please...
1. Explain briefly in one(1) sentence what is the function of the squirrel cage winding inthe operation of the synchronous motor.(for 50 points)
A 4400V, 3-ph, Y- connected synchronous motor has an effective resistance and synchronous reactance of 32 and 192 per phase respectively. If the open-circuit generated emf is 4800V between lines, calculate 1-The Maximum total mechanical power that the motor can develop . 2-The current. 3-P.F at Maximum mechanical power. 4-Total Cu losses. 5-Input power to motor.
A 400V, three phase, 4-pole, star connected SM has a synchronous reactance of 1.5 ohm per phase We field current has been adjusted so that the torque angle is 14 mechanical degrees when power supplied by the generator in 90 kW. Find 1 ) Ephi 2 ) Armature Current . 3) maximum power could supply if the field current remains constant
A 80 MVA, 33 kV, 3-phase, 60 Hz round-rotor (non-salient-pole) synchronous generator with negligible armature resistance and synchronous reactance of 9 ohms per-phase is connected to an infinite bus and delivers the rated power at lagging power factor of 0.85 and the rated terminal voltage. ▪ Determine the internal voltage of the machine and its power angle.
DC Electric Machine: synchronous machine: Which option is correct for the graph given regarding the synchronous machine? The order should be: name of the characteristic / run in (1) / run in (2) / run in (3) A) Idle running characteristic of the motor / capacitive / ohmic / Inductive. B) Setting characteristic of the generator / Pure inductive / ohmic / Pure capacitive. C) Setting characteristic of the generator / Inductive / ohmic / capacitive. D) External characteristic of the generator / capacitive / ohmic / Inductive. E) External characteristic of the motor / Inductive / ohmic / capacitive
The prime mover driving SG is lost, but the machine remains connected to the large power system and the field supply also remains on. The machine will: Select one: a. get burnt b. behave as a Synchronous Generator with no change c.behave as a synchronous motor and rotate in the same direction d. behave as a synchronous motor but rotate in a reversely
------ What is the difference between the servo motor and the stepper motor in construction, principle of works and applications ?
A shunt generator with a capacity of 250 kW and a voltage of 250 V has an armature circuit resistance of 0.05 and a field resistance of 50ohms, as well as a stray power loss of 1500 watts. Using a 9 percent overload scenario, compute the efficiency of the system.
I need help on parts 4 and 5. Also, i am confused on computing the output torque.
2. Differentiate D.C. Shunt & Series Motors? (: Suhmittin Ossign mont ono dov oftor tho