write a program that takes in three arguments, a start temperature (in Celsius), an end temperature (in Celsius) and a step size. Print out a table that goes from the start temperature to the end temperature, in steps of the step size; you do not actually need to print the final end temperature if the step size does not exactly match. You should perform

write a program that takes in three arguments, a start temperature (in Celsius), an end temperature (in Celsius) and a step size. Print out a table that goes from the start temperature to the end temperature, in steps of the step size; you do not actually need to print the final end temperature if the step size does not exactly match. You should perform

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write a program to find out the grade of a student based on the marks obtained in three subjects. The grade is calculated as: If average is 80 or greater than 80, grade is ‘A’. If average is less than 80 and greater then 50, grade is ‘B’. If average is less than 50 and greater then 33, grade is ‘C’. If average is less than 33, grade is ‘F’
Write a program that translates a letter grade into a number grade. Letter grades are A, B, C, D, and F, possibly followed by + or –. Their numeric values are 4, 3, 2, 1, and 0. There is no F+ or F-. A + increases the numeric value by 0.3, a – decreases it by 0.3. However, an A+ has value 4.0. Enter a letter grade: B- The numeric value is 2.7.
Write a program that accepts an integer number and determines whether the number is "EVEN" or "ODD. If it is even, compute the square of the number and display the message “Even number”. If the number is odd, compute and print the cube of the number and also display the remark "Odd number" , else display a remark "The number entered is zero."
Write a program that compares the area of two rectangles. You can do this several ways, one way is to add the length and width of each rectangle to get it's area and then compare the two areas together. The program should ask for the length and width of two rectangles and then tell the user which rectangle has the greater area, or if the areas are the same. The area of a rectangle is the rectangle's length times its width. Name the source code file yourName_HW4.py. Test and run the program. Capture the output console and save it as an image file named
Write a program that displays a table of pounds and equivalent weights in kilograms. You can find the conversion factor online if necessary. Store this factor in a properly named constant. Allow the user to specify the range of pounds for the table by prompting for the start, stop, and step values for the pounds column. Display the pounds accurate to two decimal places centered in a column 10 characters wide. The kilometers should display accurate to three decimal places and right-aligned in a column 12 characters wide (see page 75-78). Column headings should be displayed with the same alignments. See Sample Output.
Write a program that computes the theoretical flame temperature when a mixture of methane, propane, n-butane, and n-pentane (0% to 100% mole methane in 5 % increments; 0 to 100 mol% propane in 5% increments; 0% to 100% mole n-butane in 5 % increments) at 25°C is burned with excess air (0% to 100% excess in 5% increments) preheated to preheated to (50°C to 200°C in 10°C increments)
Write a program that displays a table of speeds in kilometers per hour with their values converted to miles per hour. The table should display the speeds from 40 kilometers per hour through 120 kilometers per hour, in increments of 5 kilometers per hour. (In other words, it should display 40 kph, 45 kph, 50 kph and so forth, up through 120 kph.) MPH = KPH * 0.6214
Write a program that displays all the numbers from 300 to 400, 5 per line, that are divisible by 3 or 6, but not both. Numbers are separated by exactly one space.
Write a program that takes in an integer in the range 11-100 as input. The output is a countdown starting from the integer, and stopping when both output digits are identical. Additionally, output the distance between the starting and ending numbers (ex: 93 - 88 = 5) Note: End with a newline. Ex: If the input is: 93 the output is: 93 92 91 90 89 88 5 Ex: If the input is: 11 the output is: 11 0 Ex: If the input is: 9 or any value not between 11 and 100 (inclusive), the output is: Input must be 11-100 For coding simplicity, follow each output number by a space, even the last one. Use a while loop. Compare the digits; do not write a large if-else for all possible same-digit numbers (11, 22, 33, …, 99), as that approach would be cumbersome for larger ranges. Hint: To practice incremental development, start by writing code that just outputs the countdown until matching digits and submit to get most of the points. Then, update your code to output the distance.