Workshop safety Enumerate commonly used PPE's and their uses

Q: why should you wipe off the outside of a zerk fitting before injecting grease into it

A: Solution:

Q: Technician A stresses the need to follow the manufacturer's recommendations for preventive…

A: Every vehicle is delivered with a service manual with manufacturer’s recommendation. The…

Q: A mirror and a quality light for leak testing may be used in lubrication repair. Select one: O True…

A: General components used for lubrication repair are: Wrenches of different sizes to remove the oil…

Q: What is a solution to the following environmental risks in a SADA system Temperature Corrosion…

A: SADA system stands for Solar Array Drive Assemblies. These are the system in which the solar array…

Q: Industrial Pipes: Because it does not have a way to access the entire internal part of a pipe, this…

A: The question is asking about a type of industrial equipment that is difficult to inspect internally…

Q: According to the OSHA Hazard Communication Standard, seven types of hazard identification ar…

A: When chemicals are used in the workplaces there must be safety ensure in case of any hazard. In…

Q: Where should vibration transducers be placed?

A: The location and installation of the vibration sensor are two of the most critical parts of the…

Q: Different types of equipment wind power system (whole)?

A: The Major parts or equipment in wind power systems are as follows: 1. Tower 2. Nacelle 3. Rotor 4.…

Q: fires

A: A spark is created when the applied electric field exceeds the dielectric breakdown strength of the…

Q: The circuit breaker at a power seat motor continuously trips: Technician A says that this could be…

A: The reasons for which a circuit breaker trips are as follows:Excess current flow due to overloaded…

Q: What type of bearing is recommended for a dirty environment?

A:

Q: An overheating vehicle is being discussed. Technician A states that the vehicle may be overheating…

A: Given Data: An overheating vehicle is being discussed. Technician A states that the vehicle may be…

Q: What are some important considerations when performing a handgrip dynamometer test?

A: Soln:- The important consideration when performing a handgrip dynometer test :- 1.This instrument is…

Q: Why should a technician not file the rough surface on the contractors contacts

A: Solution:

Q: The shielding gas used on carbon steel is ____.  A. Helium  B.Argon  C. Argon, or a mixture of…

A: The shielding gas used on carbon steel is CO2, or a mixture of CO2 and Argon option D will be…

Q: In the event of a spill of gearbox oil in the workshop, what workplace health and safety procedures…

A: During the working in any workshop, there are so many machines which may be in running condition or…

Q: If the first digit of the diagnostic trouble codes is a zero (0) what does it mean

A: When a vehicle’s on-board diagnostics system detects a malfunction, it generates the appropriate…

Q: True or False? Safety of the material handling process should be determined after the system is put…

A: The safety of material handling process should be determined after the system is put in place and…

Q: What is the use of pressure gauge?

A: Pressure gauge is used to measure pressure of  fluid which also specify the force that fluid is…

Q: There are many ways to clean parts while they arebeing serviced. These methods can be groupedinto…

A: Given Cleaning parts To find Categories of cleaning

Q: Lockout locks: Can be used to lock tool boxes, storage sheds, etc. Can be used only for lockout…

A: Lockout locks are used to lock out machinery or area until maintenance is completed. They are not…

Q: Q10. A good bullet proof vest should have these criteria. A. Deflects bullets B. Stops bullets C.…

A: The favorable properties of good bullet proof are mentioned below. Answer: A C D

Q: The only thing that can keep you safe consistently is __________________   a. Obeying all warning…

A: We have to give answer this question The only thing that can keep you safe consistently is

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.