wooden beam ( sg= 0.64) is 150 mm by 150 mm by 6m and is hinged at A as shown in the figure. Assuming unit weight of water is 9.79 kN/cu.m. a.) Determine the length of the beam submerged in water? b.) At what angle will the beam float in the water?  c.) And determine the buoyant force that causes the beam to be submerged at an angle of theta from horizontal.

Q: Question 25 Which of the following most nearly gives the slope at B? A 0.000361 rad B 0.000115 rad…

A:

Q: Current Attempt in Progress The beam cross section shown below has been proposed for a short…

A:

Q: A horizontal simply-supported beam is loaded as shown in Figure 1. It has a rectangular cross…

A: h = 70 mm

Q: Problem 1 A simply supported wide-flange beam has the cross-section and loading as shown in the…

A:

Q: The cantilever beam shown in the figure consists of a rectangular structural steel tube shape [E =…

A:

Q: Part 2: By Super Position Consider the simple supported beam shown in the Fig. a. Determine the…

A:

Q: 2. The beam shown has a rectangular cross section 4 inches wide by 8 inches deep. Compute the value…

A:

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: Macaulay's Method : We are using this method as the loading is not same through out the span…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: From the given beam and loading shown it is required to compute the slope of the beam at B and the…

Q: 2. A beam with an inverted T-section is loaded as shown. Determine the following: a. Magnitude of…

A:

Q: 3. Determine the components of the force and its moment about point A. 2m Sign Convention: 13 20N +…

A:

Q: Consider the cantilever beam shown below under the action of a 3 kN point load and a 1 kNm moment…

A:

Q: Determine the moment of inertia of the closed area with respect to the x and y axis as shown in…

A: divide the figure into rectangle and two semi-circles.therefore,area of…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 200 GPa; I = 450 ×…

A:

Q: For the beam and loading shown in Figure, determine the beam deflection at point E. Assume that EI =…

A: EI = 6 × 104 KNm2  Determine the deflection at point-E of the beam.

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 200 GPa; 1= 350 × 106…

A: Given: E=200 GPaI=350×106 mm4P=50 kNw=20 kNmLAB=1.50 mLBC=2.50 m To find: (1) Deflection at A. (2)…

Q: A simply supported beam hinged at A and supported at C, is carrying a distributed load and a point…

A: Free body diagram -  Force in the vertical direction -  ∑FY = 0⇒RA + RC - 120 - 15×2 = 0⇒RA + RC =…

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A:

Q: force Pheeded Also, determine the proper placement x of the hook for equilibrium. Neglect the weight…

A: To find value of force P

Q: The portable floor crane in the automotive shop is lifting a  350-lb engine. For the position shown…

A: W=350lb

Q: use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the…

A:

Q: In the figure below, the beam is cantilevered from the wall. The connection of the beam to the wall…

A: Given: The length of beam AB is 10 m. The weight applied a point B is 1 kN. The weight of the beam…

Q: A 1-meter-long, simply supported copper beam (E = 117 GPa) carries uniformly distributed load q. The…

A:

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A:

Q: A 10 m long beam has a 3 kN point load applied to the cantilever steel beam. The load is applied 4 m…

A:

Q: For the load beam shown derive the equation of the beam deflection y(x) along the beam. EI is…

A: The following figure shows the Free Body Diagram of the beam. Adopt the Slope Defection Method for…

Q: ation, determine the deflection at the free end of the beam shown 60 kN 300 kN–m 5 m 5 m L= 10 m El…

A: Consider the given figure Moment at fixed end due to point load at C  MA=60×10      =600 kNm

Q: Q.2) A simple beam of span length 3.2 m carries a uniform load of intensity 48 kN/m. The cross…

A: Given Data : Span = 3.2m Uniform load intensity = 48 kn/m Wood flanges Properties : E = 10 GPa Size…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1760…

A:

Q: The beam shown in Figure below is simply supported and carries a uniformly distributed load of w =…

A:

Q: With reference to the figure below, the total force (F) of the liquid on the plane surface and the…

A:

Q: A cantilever beam is loaded as shown in figure 2 below, if a prop is to be introduced at point B,…

A: Find prop reaction at B.  Let's assume upward reaction at propB (VB) .

Q: Situation 5: An overhanging beam is loaded as shown. Determine the bending moment at C (kN-m).…

A:

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1850…

A: To find deflection at point A and B

Q: 3. A steel beam is loaded as shown in the figure. Use conjugate beam method and determine the…

A: Draw the free-boy diagram of the beam.

Q: A cantilever beam, 3.5 m long, carries a concentrated load, P. at mid-length. Given: P = 200 KN Beam…

A:

Q: The 700-N force is applied to the 100-kg block, which is stationary before the force is applied.…

A:

Q: The Howe truss shown in the diagram is loaded as shown B 6 panels at 4 m For the truss shown, F₁ =…

A: A truss is given we need to find out the vertical reactions at A and G