wo pipes with 400 and 600 mm diameters, and 1000 and 1500 m lengths, respectively, are connected in series through one 600 * 400 mm reducer, consist of the following fittings and valves: Two 400-mm 90o elbows, One 400-mm gate valve, Four 600-mm 90o elbows, Two 600-mm gate valve. Use the Hazen Williams Equation with a C factor of 130 to calculate the total pressure drop due to friction in the series water piping system at a flow rate of 250 L/

Q: Question 1 a) List out 3 devices to measure hydrostatic pressure. Explain how U-tube manometer can…

A: Hydrostatic pressure- It is defined as the pressure in which exerted by a fluid at rest due to the…

Q: Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter…

A: Given, L1 = 38 m  L2 = 45 m D1 = 5 cm or 0.05 m D2 = 15 cm or 0.15 m \ Q = 0.005 m3/s

Q: A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C- 80…

A: \We have formulaH=10.583LQ1.85C1.85d4.87Q=150lps=0.15m3sL=1km=1000md=0.4m

Q: without rupturing. Determine the maximum length, 1, allowed if the roughn 00015 ft and the flowrate…

A:

Q: Refer to the parallel piping as shown. The water is flowing at Q = 0.03 m³/s. Pipe 1 has a diameter…

A: The given data is shown below: Q=0.03 m3/sDiameter of pipe 1=100 mmDiameter of pipe 2=50 mm

Q: Question 19 A pipe connected in series has the following roughness or friction coefficients: Pipe 1…

A:

Q: In the supply system (Q=0.89cfs) shown in the figure, the pressure required at the delivery end is…

A: Q = 0.89 cfs Diameter = 4 in = 0.333 ft Length = 1000 ft Pressure at delivery end = 65 psi Water…

Q: TANK TANK DATUM DATUM. DRAW AND LABEL VELOCITY HEAD DRAW AND LABEL PRESSURE HEAD (STATIC) Pressure…

A:

Q: P+ 5pV² + pgz = C,

A:

Q: Two vats are connected by a submerged pipe with a square cross-section, as shown in Figure Q2. A…

A: h2 > h1 Let density of fluid be ρ

Q: discharge pipe in which the velocity is 2.40m/sec. At point A in the suction p pressure is - 40kPa.…

A: Given:- diameter =200mm  discharge pipe dimater =150mm  To find:- Power

Q: A factory's piping system connects two tanks by a conduit system shown below. Determine the pressure…

A:

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A:

Q: D washer (2) n holes of diameter D. To reduce water consumption, a washer is installed in the shower…

A: Velocity in the pipe without reducer at section 1 and at the outlet (considering it as 2):…

Q: Problem 3. A 30 cm pipe is connected by a reducer to a 10 cm pipe. Points 1 and 2 are at the same…

A:

Q: For the system shown in the figure below, find the discharge in each pipe v-1.003-10 m³/s; 7-9810…

A: We know that friction factor is given by ; 1F = 2 log10 Re + 1.74 - For Pipe 1 : 1F1 = 2 log10 Re +…

Q: Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in…

A: ##Calculation of diameter of Pipe 2 using hazen Williams equation

Q: 4) Two tanks of liquid with v-1.02x10-6 ms are connected by two pipes in series as show in the…

A: Given: D1=0.305mD2=0.610mL1=610mL2=9140mE=0.0030ma=0.0566 m3/s To find: H

Q: A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 90…

A: assuming all value given in mks system C=1nR16 where R =hydraulic radius=D4 for pipe  C=10.015X…

Q: Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of…

A:

Q: Water at 25°C is pumped into the galvanized iron pipe branch consisting of two 50-mm-diameter pipes…

A:

Q: A rigid pipe has a diameter of 150 mm and a length of 1020 m. The water flowing in the pipe has a…

A:

Q: (3) Water jet 0.05 m- (2) 0.8 m •(1) 8X.X kPa 0.1 m Figure Q2 (b) (i) Determine the flow rate at the…

A:

Q: The figure shows a portion of a hydraulic circuit. The pressure at point B must be 250psig. When the…

A: Given data: Pressure at point B, PB=200 psig   Volume flow rate, Q=80galmin   Specific gravity…

Q: Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow…

A:

Q: The fluid in the tank is water. Flow is steady state, incompressible and nonviscid. It is known that…

A: Using the Bernoulli's equation between the tank and the point 1 -  Patmρg + v122g + Z1 = P1ρg +…

Q: In the simple hydraulic circuit shown in Figure 1 below, why is the counterbalancing pressure valve…

A:

Q: What are some of the major drawbacks to functional silos

A: Silo is a pit structure that is used to store the heavy materials like cement, carbon black etc in…

Q: c) For the system shown in Figure 3.1, calculate (i) the volume flow rate of water from the nozzle…

A: To find (a)Q=? (b)Pa=?

Q: taining air and water is shown. At the closed end of the manometer the air pressure is 16…

A:

Q: SAE 10W30 oil flows from one tank to another when the gate valve is fully opened as shown in the…

A:

Q: For the system in the figure, calculate the distancevertical between the surfaces of the two…

A: Step 1:QStep 2: Step 3: Step 4:

Q: Flowing water in pipe 1 and pipe 2 is flowing to pipe 3 which is 7m long and discharges the water to…

A:

Q: A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 100…

A:

Q: Q2/Three pipes are connected in series as shown in figure below. Flow rate is 0.02 (m³/s) and…

A: f = 0.01  Diameter of equivalent pipe (Deq) = 200mm = 0.2 m  Discharge (Q) = 0.02 m3/sec  Determine…

Q: A pipe connected in series has the following roughness or friction coefficients: C- 90…

A:

Q: At night, water is pumped from a treatment plant reservoir through distributing piping to an…

A:

Q: Consider the pipe system with EGL and HGL shown in the figure below. Which of the following…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?