With the sensor connected to the p3.5 pin on a conveyor, the packaging connected to the p0.4 pin will be activated at every 168 product pass. The Mode0 will be used for the solution. Write the required program code using the interrupt structure.

With the sensor connected to the p3.5 pin on a conveyor, the packaging connected to the p0.4 pin will be activated at every 168 product pass. The Mode0 will be used for the solution. Write the required program code using the interrupt structure.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter6: Ground-fault Circuit Interrupters, Arc-fault Circuit Interrupters, Surge Protective Devices, Immersion Detection Circuit Interrupters, And Appliance Leakage Current Interrupters

Section: Chapter Questions

Problem 24R: Briefly explain the operation of an immersion detection circuit interrupter (IDCI)....

See similar textbooks

Related questions

Q: One of the following statement is not true about Registers of a microprocessor. a. Number of…

A: registers in the microprocessor are used to store the data

Q: Refer to the logic symbol for a 74121 nonretriggerable one-shot in Figure 5-62. (a)* What input…

A: Consider the logic symbol for a 74121 nonretriggerable one-shot from Figure 5-52 from textbook. The…

Q: List 8051's primary characteristics. Explain the basic microcontroller block diagram using a clean…

A: The 8051 Microcontroller is one of the basic types of microcontrollers, designed by Intel in 1980s.…

Q: What is the device address used by the instruction OUT A4, AL

A: OUT is a mnemonic that stands for OUTput Accumulator contents to an output port whose 8-bit address…

Q: Highlight the if any important words& answer without involving Ai contentt 1732. What is a Data -…

A: Step 1: Data-efficient Image Transformer (DeiT) Introduction:The Data-efficient Image Transformer…

Concept explainers

Up-down counter

In digital logic and computing, a counter is a device that stores (and sometimes displays) the number of times a particular event or process has occurred, often in relationship to a clock. A sequential digital logic circuit is the most common type with an input line or clock and multiple output lines. In the binary or binary-coded decimal (BCD) number system, the values on the input line represents a number by several flip-flops connected in a cascaded manner. They are manufactured as separate integrated circuits and are widely used components in digital circuits. These are also a part of larger integrated circuits. These are a specific type of sequential circuit like registers or the value of the flip-flops serving as the output.

Question

Can you write the answer with assembly code using 8051 architecture?

With the sensor connected to the p3.5 pin on a conveyor, the packaging connected to the p0.4 pin will be activated at every 168 product
pass. The Mode0 will be used for the solution. Write the required program code using the interrupt structure.
Yanıt:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Required Assembly code

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need some help with the image provided. This is for microcontroller and embeded system. it seems is related to interrupts and it is providing some logical gates. Can someone explain wherever is happening in the image. I only need to grap the concepts nothing really technical
Question : with Eight LEDs with 74HC595. This code uses a shift register to use a single data pin to light up 8 LEDs. The code uses the command "bitSet" to set the light pattern. What is the value of the variable leds when the value of currentLED is 5? Hint: You can use Serial.begin(9600) in the setup and Serial.println(leds) in the loop to examine this value. Answer must be a numerical value
Q.1) What is the type of PCI transaction diagram? Redraw the timing when the IRDY# and TRDY# is ready from cycle 2 to end of transaction and explained the function of each signals appear in diagram. CLK FRAMEN AD Address Data-1 Data-2> Data-3 C/BE# Bus Cmd BE# IRDY# TRDYW DEVSEL# Data Phase Data Data Address Phase Phase Phase
PWM is the method that; 1. Sends an encrypted message. 2. Brakes a motor. 3. Creates an equivalent analog effect from digital pulses. 4. Creates an equivalent digital effect from analog pulses. 5. Runs a motor in forward and backward.
Using 8085 assembly language programming Design an emergency system for the case of a stranded plane,boat, bikers that will generate the flashing message “HELP” on the address field of the SDK-85. 10 seconds on , 10 seconds off with a total delay time of 200 seconds (10 times on/off ”HELP”) The system is activated by pressing the IV key A.) draw a flow chart based on the situation B.) indicate delay calculation (10 seconds) (value of DE) C. Convert the flow chart into assembly mnemonic (indicate RAM locations) D. Convert the mnemonics into assembly codes.
I need a concise solution to the multiple-choice problem, explained clearly.
Question 3 A pull-up resistor is essential with: O a high-speed circuit. O a TTL gate. O an open drain gate. a variable power supply. Question 4 please answer in typing format please all subpart is compulsory Spikes can be the result of" O the switching sequence of a totem-pole output. O the discharge of a decoupling capacitor. a sudden opening of the drain. too high a value of fanout.
Briefly explain the operation of an immersion detection circuit interrupter (IDCI). ___________________________
QUESTION 46 How many different types of interrupt service routines (ISRS) can be supported by the 8088? 2 256
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Which of the following are part of the Arduino microcomputer. The answer could be more than one
Design a small direct circuit used in a door bell application. The doorbell is only to rung when the push button is pressed. Use an I/O list, sketch the ladder logic and written description.