With the same loading conditions as in problem a, and to reduce the deflection at C, a roller support is added at C and the beam is divided to two parts connected by a pin joint at D as shown in figure b below. Draw the internal reactions diagrams for the beam ADBC. Hence determine the sections that feel the maximum shear force and the sections that feel the maximum bending moments and their values. M kN m w kN/m A 2 m 2 m 2 m-

With the same loading conditions as in problem a, and to reduce the deflection at C, a roller support is added at C and the beam is divided to two parts connected by a pin joint at D as shown in figure b below. Draw the internal reactions diagrams for the beam ADBC. Hence determine the sections that feel the maximum shear force and the sections that feel the maximum bending moments and their values. M kN m w kN/m A 2 m 2 m 2 m-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) For what values of m is y = Aemx a solution of y" – 3y' + 2y = 0
Question 2 Calculate the current i1 if R1 = 7 Ohms, R2 = 6 Ohms. R3 = 3 Ohms, R4 = 8 Ohms, and Vs = 39 Volts. R1 ww Vs R2 R3 R4 ww 券 Nex Su No new data to save. Last checked at 2:30am ww ww
!
The windscreen washers of an old car don't work (W = 0). This could be for two reasons: the windscreen fluid tank is empty (E = 1) or the tube is has a blockage (B = 1). Being an old car, the light to indicate that the windscreen fluid tank is empty only comes on (L = 1) 75% of the time. It will sometimes comes on even if the tank has some fluid in it, with probability 0.25. Of course the tube could be both blocked and the tank empty. (a) Draw the Bayesian network describing the scenario just described, and express the joint probability in factorised form, defining appropriate variables.
!
Hw/ y= lux f Y=e? Find Df R. Hw/ solve: O log (x)+Log (x-1) = log (8x-12)-1a9L2) %3D An s/x=3 %3D
A left hand threaded 14 mm diameter A36 steel bolt is stuck in a metal block. Assume the bolt head is flush with the block surface at A. In order to remove the bolt the 50 Nm torque is applied to the bolt head as shown. The block applies a resisting torque "t" to the stuck threads which is assumed to be uniformly distributed along the 50 mm buried depth. G = 75 GPa a) Explain the difference between right and left hand threaded bolts Determine: b) The magnitude of the uniform resisting torque "t" (including proper units) c) The internal torque as a function of x measured from B (a FBD is required) d) The maximum shear stress in the bolt Ans: 92.8 MPa e) The angle of twist of bolt head A with respect to end B Ans: 0.0044 rad f) The largest torque that can be applied to the bolt head before it twists off (Tyield = 150 MPa) %3D
Problems 5-111 through 5-116 Figures P5-111 through P5-116 show completed shearing force diagrams for beams. Develop the loading diagram and the bending moment diagram for each beam.
Topic: ꜱʜᴇᴀʀ ᴀɴᴅ ᴍᴏᴍᴇɴᴛ ɪɴ ʙᴇᴀᴍᴅʀᴀᴡ ᴛʜᴇ ꜱʜᴇᴀʀ ᴀɴᴅ ᴍᴏᴍᴇɴᴛ ᴅɪᴀɢʀᴀᴍ.
X2 5KN X2 X2 Tau = 7omPa %3D X = 150 !! d- ? X2 = 70 %3D
Please help :( please please M = 1 N = 1