with switch SW1 closed, current I, = 2A. With switch SW1 open, what is the Norton equivalent circuit as seen by R,? Note that your answer should NOT be in terms of the unknown voltage V, and unknown current I,. I, 122 RL V, 62 SW, +

Q: 7. R G₁ 64 Gs 6₂ H₂ Ga

A:

Q: The current in a second order source free series RLC circuit is given as iz(t) = e-40t . (B,cos(60t)…

A: Given  iL(t)=e-40t.(B1cos(60t)+B2sin(60t))

Q: G3 H2 R(s) Y(s) G, G2 -H,

A:

Q: ww 20 V 1/8 F t = 0

A:

Q: Get the transfer equation from this circuit, and get its block diagram without using reduction…

A: A block diagram is a graphical representation of a system or process using simple, standardized…

Q: Which of the following networks are closed networks, given that P is open, Q is closed, R is closed,…

A: As this network has closed loops, hence this is a closed network.

Q: How did the output become like this? Can you explain the steps? 3 = (s³ + 8s² + 18s)I2 from this…

A: solutionGiven that1s=1+3s*13s2+5s+3I2-3s*I23=s3+8s2+18sI2

Q: In the following block diagram find the following four transfer functions. C₁(s) R₁(S) R₂ (s)-0 R₁…

A: Given the block Diagram is  where two input  R1 and R2 and two output response is C1 and C2  and…

Q: Two teachers (A, B) will grade two questions in an exam. Tacher A will grade question 1 which is 60…

A: Case 1: When the student gets 20 marks from the teacher A, the student will be successful only if…

Q: Draw the pole-zero diagram of the following network functions:

A: a) Given network function F(s)=5s-12s2+4s+13

Q: Convert the block diagram in Figure 2 into a block diagram and apply the Mason's formula to…

A: Given:   To find: To convert the signal flow graph in block diagram. To calculate transfer…

Q: Discuss similarities and differences between RL and RLC Circuits. How can one tell if an RLC circuit…

A: Load- It is defined as the elements or equipment which are responsible for the dissipation of the…

Q: Reduce the following block diagrams using the block diagram reduction method

A:

Q: 1- Explain the effect of increasing and decreasing of resistor's value on series and parallel RLC…

A: We need to explain the effect of increasing and decreasing of resistor's value on series and…

Q: (2) Draw a block diagram for the following dyamic model, with X(s) as the output and F(s) and G(s)…

A: To solve above problem, one should know about transfer function of a system. Transfer function of a…

Q: 1. Construct a Routh table to analyze the stability of the following system, D(s) = s² + s² + 2s +24

A: Given system characteristics equation, Ds=s3+s2+2s+24

Q: G, R G, G. G2 H

A:

Q: For the block diagram given in figure 2; Find the transfer function from R(s) to Y(s). Find the…

A: The given block diagram can be reduced by considering the parallel and series connected block…

Q: eece v(4)

A: State variables

Q: If a, < < a? and the roots are real and the same then the response of an RLC circuit is said to be O…

A: Given condition: ω02&lt;α2 and the roots are real and same.

Q: We wish to carry out a subtraction using the circuit shown below.  We will subtract A - B where A =…

A:

Q: Consider the block diagram with R(s) an unit step input. The response of the output will look like…

A: Given : A closed loop system with open loop transfer function 1/sT And unit step input is applied…

Q: Reduce the block diagram shown in the figure below to a single block, T(s)=C(s)/R(s)

A:

Q: For a parallel RLC circuit operating under initial conditions only: a) Give detailed discussion of…

A: The parallel RLC circuit having only the initial condition, Parallel circuit has three type of…

Q: The counters are used in cascading in order to achieve the higher modulus operation. A certain…

A: To obtain a modulus of 39000, we will need a minimum of 16 flip-flops. The IC 74HC161 consists of…

Q: To design a counter which count in the following sequence 0,1,3,5,7 by * using T-F.F, the input of…

A: The required counter can be designed by using the State transition table and the simplified Boolean…

Q: Find Gensul of this R-L-C -Crcuit ! C=0,0833 F E= 10v R=22 ell しニ2H

A:

Q: following this proceduress- Step Li- S=-Jw Step 31- then sketch 30 <= jw, Step2; s= lim Re Rises ,…

A:

Q: A series RLC circuit is described by di d²i L +R + dt² dt i с = 2 Find the response when L = 0.5H, R…

A: In this question, we need to determine the current i(t). We solve this equation using the Laplace…

Q: Which of the following are wrap-around cells in a 3-variable K-Map? O (4,6) (1,7) (2,3) O (0,1)

A: Choose the correct Which is the following the Wrap around cells in 3 variable K map?

Q: Q1// Find root locus for transfer function below: -s-35 +5 GH = 2 s+5s +9S +3

A: The root locus plot is used to plot the closed loop poles of a given system represented by it's…

Q: How do you find the coefficients in the underdamped case in an RLC circuit?

A: Whether it is series RLC or parallel RLC use the same equation but here use the initial conditions

Q: What are the initial conditions for the circuit shown? Ta ll İL 1N L R3 ic t= 0 C = VC Vs 2NŽR2 6 V…

A: We know the behaviour of inductor and capacitor at steady state and initial state . So we will find…

Q: Mason's rule

A:

Q: Find the step response of the basic RL circuit. Show correct equations.

A:

Q: G4 R(s) C(s) G G3 Hz

A:

Q: 2. Find out the transfer function by reducing the blocks. R(s) G₁ G₂ H₁ H₂ Figure a H3 G4 G3 G5 Y(s)

A: The block diagram reduction method is used to determine the transfer function for the system.This…

Q: For each of the following circuits, find the output and design a simpler circuit that has the same…

A: Solution is given below.

Norton Theorem

In the current circuit law, the Norton theorem (also known as the Mayer-Norton theorem) is a simplification that can be applied to networks generated by a constant line of opposition, power sources, and current assets. In two network terminals, it can be switched on with a current supply and single resistor respectively.